![background image](http://html.mh-extra.com/html/noctua/nm-am4-uxs/nm-am4-uxs_installation-manual_1698743001.webp)
Dear customer,
Congratulations on choosing a Noctua cooler for your AMD AM4 system.
We always like to think of our coolers as safe long-term investments: Not
only are they built to last, we also provide upgrade kits so that you can
keep using your trusty Noctua heatsink when you do a system upgrade.
Enjoy your Noctua cooler on AM4!
Yours sincerely,
Roland Mossig, Noctua CEO
This SecuFirm2™ Mounting-Kit for AM4 is compatible with the NH-U14S,
NH-U12S and NH-U9S. For detailed, up to date compatibility information
please visit: www.noctua.at/am4
This manual will guide you through the installation process step by step
using an NH-U12S heatsink as an example. The installation procedure is
identical for all compatible models.
Prior to installing the cooler, please consult the compatibility list on our
website www.noctua.at/compatibility and verify that the cooler is fully
compatible with your motherboard. Please also make sure that your
PC case offers sufficient clearance for the cooler and that there are no
compatibility issues with any other components (e.g. tall RAM modules).
Double check that the heatsink and fan clips do not make contact with
the VGA card or other PCIe cards. Noctua cannot be held responsible for
any damage or losses caused by compatibility issues.
Should you encounter any difficulties, please check the FAQs on our
website and don’t hesitate to contact our support team at support@
noctua.at. Noctua cannot be held responsible for any damage or losses
caused by compatibility issues.
Multilingual versions of this manual are available on our website:
www.noctua.at/manuals
Required mounting parts:
AMD stock backplate
(pre-installed on the motherboard)
2x NM-AMB6 mounting bars
2x NM-AMB7 mounting bars
4x NM-ALS1 screws
Attaching the mounting bars
Step 2
Choose either the short NM-AMB6 or the long NM-AMB7 mounting bars
according to the desired final orientation of the cooler.
First put the plastic spacers onto the screw threads of the backplate, then
fix the mounting bars using the four long screws.
Orientation NM-AMB7
Orientation NM-AMB6
Removing the stock retention module
Step 1
First remove the motherboard’s stock CPU cooler retention module by
unscrewing it from the backplate. The SecuFirm2™ mounting system will
install directly to the stock backplate, so please keep it in place.
If your motherboard does not include a stock backplate, please contact our
customer support at [email protected].
NM-AMB6
Caution: Gently tighten the screws until they stop, but don’t use excessive
force (max. torque 0.6 Nm).
For the short NM-AMB6 mounting bars, make sure that the curved sides
are pointing inwards. For the long NM-AMB7 mounting bars, make sure
that the curved sides are pointing outwards.
NM-AMB7 mounting bars
NM-AMB6 mounting bars
Step 3
Applying thermal paste
If there are residual traces of thermal paste or thermal pads on your CPU
on the base of the heatsink, please clean them off first. Then press a small
drop (4-5mm diameter) of thermal compound (e.g. Noctua NT-H1) onto
the centre of the heatspreader.
NM-AMB7
4x NM-APS4 plastic spacers
Noctua NM-AM4 UxS
|
Installation Manual
Caution: Applying too much thermal paste will lower heat conductivity and
cooling performance!
Fastening the heatsink to the CPU
Caution: If you’re using the cooler for the first time, please take off the
protection cover at the bottom side of the heatsink first!
Step 4