Instruction Sheet
Subject: BIC Tune Up
SCOPE: MULTIPLEX BIC UNITS MA-8-2, MA-8-2BF, MA-8-2AF
1 of 9
Document Number: 020009017 May 12, 2022
MULTIPLEX
645 PARK EAST BLVD SUITE 5, NEW ALBANY, IN 47150
844-724-CARE
WWW.MULTIPLEXBEVERAGE.COM
Refreshing the Experience
TOOLS REQUIRED
• Safety Gloves (cut resistant)
• Oetiker Pliers (PN 00681815)
• Needle Nose Pliers
• Screw Drivers, Phillips & Flat Head
• 3/8” or ¼” Drive Socket Set (3/8” and 5/16”)
• Standard Open End Wrench Set
• Soft Bristle Brush
• Wet/Dry Shop Vacuum
• Digital Scale (weighs in ounces to once decimal place)
PARTS REQUIRED
• Food Grade Lubricant
• 5 - 6 ft (1.8m) ¼” I.D. X 3/8 “ O.D. clear tubing
• TUNE UP KIT 020009016 (contents listed below)
QTY
DESCRIPTION
PART NUMBER
9
Valve, Dispense Outlet, LMS
1706172
9
15.7 Oetiker Clamp
15.7-706R
2
O-ring, replacement
MCP00262
1
Gasket Ice Shaver
3434865
1
Drive belt, Shaver Vitamix 1617
VMP00123
2
Cup Grate O-rings
3547901
1
Instructions Tune Up ENG
020009017
1
Instructions Tune Up French
020009047
1
SHAVER BLADE KIT
VMP00125
RECOMMENDED TRUCK STOCK LIST FOR TUNE UP
QTY
DESCRIPTION
PART NUMBER
1
SWITCH REED RINSE AREA MOD
2160033
1
SWITCH REED RINSE AREA - GRAY
2162748
5
FUSE, 5A, MIXER BOARD
2193015
1
SWITCH, SNAP ACTION, MINI - BLEN HM
2194807
1
BOARD, SRB ,BIC, GEN2
2195346
2
CONTROL BLENDER BIC HSM
2195363
1
CONTROL, 7 IN UI, BIC
000-BIC-01F9-S
1
RELAY, 24DC COIL, DPDT
2196069
2
FUSE, 4A, DC HARNESS
2198785
1
PUMP, FLOJET, NSF, NO ASO
3239675
1
MIXER MTR, 6MM, 120V/50-60, GEN3 SW
3239822
2
ASSEMBLY, LOWER BLENDER, 6MM, GEN3
3239825
1
SOLENOID VALVE REPAIR KIT
020005547
1
VALVE, S.S. SLND, WATER, 1/4"
000-BIC-01B5-S
1
SAFETY SWITCH/RECTIFIER ASSEM- 120V
VMP00113
1
SHAVER BELT
VMP00123
1
SHAVER BLADE KIT
VMP00125
1
SENSOR, HALL EFFECT
VMP00175
1
SHAVER MTR W/PULLEY / MAGNET 120V
VMP00172
3
MOTOR ISOLATION MOUNT
9324159
1
PUSH ROD
VMP00134
3
CUP ALIGNMENT RING INSERT
1708685
1
GASKET, ICE SHAVER
3434865
NOTE: Additional non-warranty parts used need to be
invoiced on a separate invoice to the site. Manager or
Operator must approve additional repairs.
NOTE: All right and left references are based off of standing
in front of the unit.
,
CAUTION
Ice shaver blade is sharp on both edges. Wear cut resistant gloves
when handling.
n
Warning
Blender shaft contains sharp blades.
Wear cut resistant
gloves when handling.
Do NOT touch the blades.
