Motorola MC68360 User Manual Download

Page: 1 / 28

Order this document by

MC68360UM/AD

This document contains information on a product under development. Motorola reserves the right to change or discontinue this product without notice.

Errata and Added Information to

MC68360 Quad Integrated Communication
Controller User's Manual Rev 1

MC68360



MOTOROLA, 1995

Microprocessor and Memory
Technologies Group

SEMICONDUCTOR PRODUCT INFORMATION

January 8, 1998

This document describes the latest information and changes to the first revision of the
MC68360 user’s manual.

Section 2 – Signal Descriptions

1. QUICC Functional Signal Groups.

On page 2-2, Figure 2-1, the signal names in the left column had a typo. The corrections for
the typo are in the right column.

As seen on page 2-2

Correction

A31-A27/WE3-WE0

A31-A27/WE0-WE3

SDACK2/L1TSYNCB/CTS3/PC8

L1RSYNB/CD3/PC9

SDACK1/L1TSYNCA/CTS4/PC10

L1RSYNCA/CD4/PC11

2. Error on TRIS

On page 2-4, Table 2-1, the function description of TRIS stated that it is sampled during
system reset. This is not true. The TRIS signal is always sampled except during reset.

3. Missing Note.

On page 2-8, section 2.1.7.2 the following note should be added:

NOTE

User should note that the pin AVEC/IACK5 is always an open
drain output.

Freescale Semiconductor, Inc.

For More Information On This Product,

Go to: www.freescale.com

Summary of Contents for MC68360





























Search results

Summary of Contents for MC68360

Reviews:

Related manuals for MC68360

Brands by name

Popular brands

Motorola MC68360, User Manual

Search results

Summary of Contents for MC68360

Reviews:

Related manuals for MC68360

Brands by name

Popular brands