background image

 
 
 
 
 
 

PCI Ethernet  

UTP/BNC Card 

 

User Manual 

 

   English 

 

 

 
 
 
 
 
 
 

 

 
 
 
 
 
 
 

LINDY No. 70939 

 

www.lindy.com 

 

Introduction 

 

Thank you for purchasing the LINDY PCI Ethernet 
UTP/BNC Card. This 32-Bit PCI card supports 10Base-2, 
10Base-5 and 10Base-T networks and full-duplex 
operation (UTP/STP). 

 

Packing List 

 

ƒ

 

32-Bit PCI Ethernet Card 

ƒ

 

BNC T-Piece 

ƒ

 

Software Driver Disk 

ƒ

 

This manual 

 

Features

 

 

ƒ

 

32-Bit PCI Ethernet Card 

ƒ

 

BNC and RJ-45 Ethernet connectors 

ƒ

 

Supports Full-Duplex operation (UTP/STP only) 

ƒ

 

Plug & Play installation 

ƒ

 

Auto detects media type – BNC and STP 

ƒ

 

Complies with IEEE802.3 CSMA/CD, 10Base-2, 
10Base-5 and 10Base-T, 10/20Mbps transfer rate 

ƒ

 

Built-in LED’s to indicate network activity 

ƒ

 

Diagnostic and driver software included 

ƒ

 

Supports Netware ODI & IPX, NDIS driver for LAN 
manager, Windows 95/98/ME/2000/XP, SCO UNIX 
driver & packet driver for TCP/IP 

 

 

 

For Home and Office Use 
Tested to Comply with FCC Standards 

Hardware Installation 

 

1.  Switch off the computer and remove the case cover. 
2.  Locate an available 32-Bit PCI slot; remove the 

expansion slot blanking plate and retain the screw. 

3.  Carefully insert the card into the PCI slot. Ensure the 

card is firmly in place and secure using the retained 
screw. 

4.  Replace the case cover. 
5.  Connect the card to the network using thin or twisted-

pair cable, depending on the connector you are using. 

6.  If the card is to be used in Full-Duplex mode (UTP or 

STP only), it should be connected to a switching hub 
that supports Full-Duplex operation. 

 

LED Indicators 

 

This card is equipped with two LED indicators which 
display the card status - 
 

LINK:

 When a network link is detected this LED will light 

up. If this indicator is OFF, check the cable connections 
 

ACT:

 This LED lights up to indicate the card is powered 

up. It flashes to show network activity. 
 
 
 
 
 
 
 

Software Installation 

 

For Windows ME/2000/XP the card will be detected by the 
operating system and the software will be installed 
automatically. 
 
For Windows 95 and 98 the card will be detected 
automatically and you will be prompted to insert the driver 
disk. Please also have at hand your operating system CD 
in case Windows requires files from it.  
 
For all other operating systems refer to the Help program 
located on the supplied disk for installation instructions. 
 

Certification 

 

Note:  

This equipment has been tested and found to comply with the limits for a Class A 
digital device, pursuant to Part 15 of the FCC Rules.  
 
These limits are designed to provide reasonable protection against harmful 
interference in a residential installation. This equipment generates, uses and can 
radiate radio frequency energy, and if not installed and used in accordance with the 
instruction manual, may cause interference to radio communications. However, 
there is no guarantee that interference will not occur in a particular installation. If 
this equipment does cause harmful interference to radio or television reception, 
which can be determined by turning the equipment off and on, the user is 
encouraged to try to correct the interference by one or more of the following 
measures: 

 

Reorient or relocate the receiving antenna 

 

Increase the separation between the equipment and receiver 

 

Connect the equipment into an outlet on a circuit different from that 
which the receiver is connected 

 

Consult the dealer or an experienced radio/television technician for help

 

 

 

 

 

 

       

 

 

 

 

 

 

 

 

 

 

 

 

 

 

            January 2005

 

Reviews: