WARNING: Carefully read following instructions and technical specifications
in this manual before installation. The system must be installed and used only ac-
cording to this manual. The system is designed for vehicles with 12V power sup-
ply. It has to be connected to 12V output and to the ground. Neither producer or
seller of the system is responsible for damages caused by incorrect installation,
using or operating of this product. Unprofessional operation or modification of
the system can damage the system alone, or the electric system of the vehicle
and leads to warranty loss. For proper working of the system we recommend
the installation to be made by authorized service.
I.SYSTEM DESCRIPTION
The KEETEC TS IMO is anti-theft system with smart detection and two circuits of im-
mobilization dedicated for vehicles with 12V power supply. TS IMO use 2 modes of
system deactivation: by button on transmitter or by contactless transmitter - automati-
cally if transmitter will be in range or system may be deactivated via E-card. Second
mode use both - transmitters and E-card together.
II. PROGRAMMING REMOTE CONTROLS
The system can learned maximum 3 pcs transmitters.
- System is deactivated, turn ignition ON, press valet switch 5 times within 10 sec-
onds.
- Turn ignition off. If security mode is not activated (function F4), siren/buzzer will chirp 5
times to enter code learning mode.
- When security mode is activated (function F4), LED diode starts flashes slowly. Enter
security mode.
- if the LED will flash so many times which is the value of first PIN number, push the
service button one time. LED will start to flash again.
- if the LED will flash so many times which is the value of second PIN number, push the
service button one time. LED will start to flash again.
- if the LED will flash so many times which is the value of third PIN number, push the
service button one time. LED will start to flash again.
- if the LED will flash so many times which is the value of fourth PIN number, push the
service button one time. If you entered correct PIN code, siren/buzer sounds 5 times
and LED diode lights permanently.
System enter to learning mode.
- Then press the transmitter button within 10 seconds, siren will chirp the times of trans-
mitter’s sequence. E.g. one chirp for the first transmitter, two chirps for the second
transmitter, and three chirps for the third transmitter.
- If a new remote control is to be programmed, all existing remote controls have to be
reprogrammed at the same time.
- After programming, turn ignition ON or wait 10 seconds, exit programming mode,
enter the disarm mode and recount the 30 seconds.
III. CODE LEARNING FOR E-CARD
The system can learned maximum 3 pcs E-Cards
- System is deactivated, turn ignition ON, press valet switch 6 times within 10 sec-
onds.
- Turn ignition off. If security mode is not activated (function F4), siren/buzzer will chirp 6
times to enter code learning mode.
- When security mode is activated (function F4), LED diode starts flashes slowly. Enter
security mode.
- if the LED will flash so many times which is the value of first PIN number, push the
service button one time. LED will start to flash again.
- if the LED will flash so many times which is the value of second PIN number, push the
service button one time. LED will start to flash again.
- if the LED will flash so many times which is the value of third PIN number, push the
service button one time. LED will start to flash again.
- if the LED will flash so many times which is the value of fourth PIN number, push the
service button one time. If you entered correct PIN code, siren/buzzer sounds 6 times
and LED diode lights permanently.
System enter to learning mode.
- Take one E-card near the antenna coil within 10 seconds. If over 10 seconds or turn
ignition ON the system will exit code learning E-card mode automatically.
- The siren will chirp accordingly for confirmation as soon as the code is learned. For
example, the first E-card is learned, the siren will chirp once. The second E-card is
learned, the siren will chirp twice. (3 pcs maximum).
- If one of the E-card is to be programmed, the other E-card must be reprogrammed
at the same time.
- After programming, turn ignition ON or wait 10 seconds, exit programming mode,
enter the disarm mode and recount the 30 seconds.
Note:
Don’t put the two E-card together when using, otherwise the detect range will
be affected.
KEETEC TS IMO
CONTACT LESS IMMOBILIZER WITH SMART DETECTION INSTALLATION MANUAL
EN
IV. PIN CODE CHANGE
( factory preset PIN NUMBER: 4321)
- Turn on the ignition and push the valet button 10 times within 10 seconds.
- Turn the ignition off. Enter security mode.
- If you entered correct PIN code, siren will sound 1 time and LED diode lights no longer.
- Now you are in PIN programming mode.
- LED starts flashing and you can enter a new PIN code.
- if the LED will flash so many times which is the new value of first PIN number, push the
service button one time. First PIN number is saved. LED will start to flash again.
- if the LED will flash so many times which is the new value of second PIN number, push
the service button one time. Second PIN number is saved. LED will start to flash again.
- if the LED will flash so many times which is the new value of third PIN number, push
the service button one time. Third PIN number is saved. LED will start to flash again.
- if the LED will flash so many times which is the new value of fourth PIN number, push
the service button one time. Fourth PIN number is saved.
- 5 seconds after entering the fourth code number LED diode will show the new PIN
code with the number of flashes with 2 seconds pause between every number.
- Turn the ignition on or wait for 10 seconds after showing the new PIN code and system
will automatically end the PIN code programming mode
Note:
Keep your new PIN code in safe. In case of lost please contact your dealer.
V. SERVICE MODE
- Turn on the ignition and press service button 2 times within 8 second. Turn off the ignition.
- If security mode is not activated, siren/buzzer sounds 2 times and LED lights permanently.
Service mode is activated.
- When security mode is activated (function F4), LED diode starts flashes slowly. Enter
security mode.
- if the LED will flash so many times which is the value of first PIN number, push the
service button one time. LED will start to flash again.
- if the LED will flash so many times which is the value of second PIN number, push the
service button one time. LED will start to flash again.
- if the LED will flash so many times which is the value of third PIN number, push the
service button one time. LED will start to flash again.
- if the LED will flash so many times which is the value of fourth PIN number, push the
service button one time. If you entered correct PIN code, siren/buzzer sounds 2 times
and LED diode lights permanently. Service mode is activated.
Deactivation of service mode
Turn on ignition and press the service button 2 times within 8 seconds. Turn off the
ignition. Siren/buzzer sounds 2 times and LED diode lights no longer. Service mode is
deactivated.
Also, service mode may be activated by the E-card - turn on ignition and put the E-
card to antenna on 20 seconds.
VI. EMERGENCY DEACTIVATION
Open the door and turn on the ignition. Push the valet button so many times, which is
the value of the first number in PIN code within 8 seconds and then turn of the ignition.
If the security mode is turned off, siren will sound 4 times and system will be disarmed.
If the security mode is armed (function F4), LED will start to flash slowly. Enter the security
mode. If you have entered correct PIN code, siren/buzzer will sound 4 times. System
will be disarmed.
MEMORY FUNCTION
- The alarm wills memory the condition although the power is cut off.
VII. PROGRAMMING SYSTEM FUNCTIONS
The immobilizer TS IMO can be programmed via valet switch or PC.
Follow this when programming functions:
1. Activate the service mode (see section VI)
2. Turn on the ignition and press service button 7 times within 10 seconds.
3. Turn off the ignition, LED will start to flash.
4. Push the valet button within 10 seconds so many times, that corresponds to the
number of the function you want to set up. Siren will sound after each push of the
valet button.
5. Turn the ignition on. Siren/buzzer will sound 1 or 2 times, depending on which
setting was set. Turn off the ignition.
6. You can repeat programming by turning the ignition on. Using the same way from
point “4”.
8. If 10 seconds without any action or turn ignition to off, system will chirp twice and
leave function selection mode.
9. Leave service mode.
