i
Hold 2LPro,
i
Hold 4LPro
Professional All-In-One Music On Hold device
Rev 32
•
Ensure USB Flash drive or SD card is inserted then Plug the included AC adapter
(110- 240 V AC to 5V DC)
Be sure not to use a different
power adapter or the unit will be damaged
•
Confirm that White LED lights in front of unit are double blinking–
for regular phones continue, for PBX phones go to page P4
•
Use one of your telephones and unplug the cord for L1/L2 from it and connect it to L1/L2 IN jack on iHOLD device , now
connect the L1/L2 OUT jack to your telephone using the provided cord, check for Dial Tone on lines 1 & 2
•
If applicable unplug the cord for L3/L4 from telephone and connect it to L3/L4 IN jack on iHOLD device , now connect the
L3/L4 OUT jack to your telephone using the provided cord, check for Dial Tone on lines 3 & 4
•
Observe that as you connect the lines the blinking lights turn OFF
(on non existing lines the lights keep blinking and that is OK)
•
Turn the Speaker
ON1
(for Music on Hold )
or to
ON2
(for your songs and office music)
to confirm Audio is playing and Adjust the
Volume to mid level
(you can Turn it OFF any time)
Switch set to 1: Hold button activation
Use this setting when all phones are corded ( not cordless type like corded base s portables) and all are same model
(for example all are ATT 993)
Operation:
make or receive a real call, the LED on the iHOLD turns ON solid, then simply press the button on your
telephone, the Music will be heard to the caller and the LED on the iHOLD device starts to BLINK
,
to return to the call just re-
select that line. (Be sure to allow 1 or 2 seconds before putting a call on HOLD).
The 1
st
time your are setting the device If it did not work hang up and try it again 2 or 3 times.
If music on hold does not work in this setting
(for example ATT 1040,1070,1080)
, hang up and change switch to setting 2 or 3
Switch set to 2: Flash activation
This setting utilizes
Flash then Hold
activation method, this setting supports any phone or any mix of brands with instant
activation by pressing Flash then Hold
Operation:
make or receive a real call, the LED on the iHOLD turns ON solid, then simply press the then
button on your telephone, the Music will be heard to the caller and the LED on the iHOLD device starts to BLINK
,
to
return to the call just re-select that line and speak into the audio to stop it for example say :
“Hi I am Back”
(Be sure the call
has been on Hold at least 4 seconds before you try to voice deactivate the audio)
You may also re-select the line that has been on Hold and press
to stop the audio
If for some reason you are not able to voice -deactivate, try speaking a little louder or more direct into the microphone, if that
does not work hang up and set the switch to
3
. Remember you can always use the Flash button to deactivate the audio as well.
L1/L2
OUT
110 - 240 V
HOLD
FLASH
HOLD
L1 L2
L1/L2
IN
1 2 3
A B C
Front
view
Back
view
L3/L4
IN
L3/L4
OUT
NXT /AUX L3 L4
Volume1
Audio2
External Speaker, PA
system, Bluetooth
transmitter
FLASH
1 2 3
The FLASH button could be labeled as
Call Wait
or
LINK
or
ON
or
TALK
button on some telephones
USB drive
SD card slot
Volume2
Speaker
ON1 ON2
OFF
Audio1
Output to PBX or
AUX Audio Input
P1
Do not make the volume too loud in this setting or the audio could sound flickering when heard on Hold
Program
Please note: just
one telephone
may be
connected to this
device, other
telephones
remain
connected to
their own wall
jacks and they all
work.
LED
SW
1 2 3
