background image

Sliding Door Double Cylinder Lock

Very Important! 

Please fasten all screws by hand and not an electric screwdriver or drill, as over tightening is not recommended.

Step 2: Installation of Handle - Please note the Black Markings on Cylinders and Tail Pieces. In order for this lock to work 
properly, all 4 markings must be facing each other as shown below, with the keys removed.

Remove screws from the Handle to separate it from the Lock Chassis. On a Double Cylinder lock, 
install both the inside cylinder and the outside cylinder. Feed the Tail Piece through the Cylinder 
Locator and attach the locator on the Outer Pull. The Tail Piece length is adjustable to suit door 
thicknesses. Snap at break marks for desired length. Now select two screws to suit your door 
thickness. • Use 2 x 55mm screws if your Door is 30-35mm thick, • Use 2 x 50mm screws if your 
Door is 24-30mm thick or • Use 2 x 45mm screws if your Door is 18-25mm thick.
Insert your selected length screw through the Lock Chassis through the door and into Handle by 
hand. The 4 screws remaining can be disposed of.

Instructions to install the Sliding Door Double Cylinder Lock.

If installing this lever set into a new door, you will need the following tools: 3mm pilot hole, 9mm drill bit, corded or cordless drill, hammer, wood chisel, Phillips head screwdriver, tape 
and pencil. 
If you are replacing an existing lock, remove your existing lock, clean down surfaces and follow the Installation process.

WARRANTY CONDITIONS

Any claim under this warranty must be made within 3 years of the date of purchase of the product. To make a claim under the warranty, take the product (with proof of purchase) to any Bunnings store (see www.bunnings.com.au for store locations). Romak 

Hardware Distributors Pty Ltd bears reasonable, direct, expenses of claiming under the warranty. You may submit details and proof to our store for consideration. The warranty covers manufacturer defects in materials, workmanship and finish under normal 

use. This warranty is provided in addition to other rights and remedies you may have under law: our goods come with guarantees which cannot be excluded under the Australian Consumer Law. You are entitled to replacement or refund for a major failure and 

compensation for other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. The warranty excludes damage resulting 

from product misuse or product neglect. The warranty covers domestic use only and does not apply to commercial applications. This warranty is given by Romak Hardware Distributors Pty Ltd, ABN 15489950457, 177-181 Atlantic Drive, Keysborough Vic 3173, 

(03) 9795-6789, e-mail: [email protected] 

Suits models 697460, 697470, 697480.

00566

Step 3: Installing Keeper and Striker

Unscrew the Jacking Screw and loosen 
the Fixing Screws. 
Separate the Keeper from Striker.
Line up the Striker with the Lock 
Chassis on an adjacent door frame.
Fasten the Striker to the door frame 
with screws.
Reassemble the Keeper and Striker.
Fixing Screws can be used to adjust 
Striker up and down to better fit the 
Beak locking mechanism.

Step 1: Preparation 

Correctly place template and fold 
on line A. Tape it to your sliding door 
face, at the desired height from the 
floor level, ensuring that a position 
is selected either above or below the 
existing screen door handle so that 
the handles don’t interfere with each 
other. Drill marked holes using a 3mm 
pilot hole followed by 9mm drill bit and 
continue with the installation.

Lock Chassis

Handle

Black Markings

Outside Cylinder

Inside Cylinder

Beak

Cylinder Locator

Door

Tail Piece

Outer Pull

Screw

Latch Lever

Black Markings

Striker

Keeper

Fixing Screw

Jacking Screw

Adjacent

Door Frame

Line A

25mm

Line A

Fold to Door Edge

25 mm

Lock Chassis

Handle

Black Markings

Outside Cylinder

Inside Cylinder

Beak

Cylinder Locator

Door

Tail Piece

Outer Pull

Screw

Latch Lever

Black Markings

Striker

Keeper

Fixing Screw

Jacking Screw

Adjacent

Door Frame

Line A

25mm

Line A

Fold to Door Edge

25 mm

Lock Chassis

Handle

Black Markings

Outside Cylinder

Inside Cylinder

Beak

Cylinder Locator

Door

Tail Piece

Outer Pull

Screw

Latch Lever

Black Markings

Striker

Keeper

Fixing Screw

Jacking Screw

Adjacent

Door Frame

Line A

25mm

Line A

Fold to Door Edge

25 mm

Lock Chassis

Handle

Black Markings

Outside Cylinder

Inside Cylinder

Beak

Cylinder Locator

Door

Tail Piece

Outer Pull

Screw

Latch Lever

Black Markings

Striker

Keeper

Fixing Screw

Jacking Screw

Adjacent

Door Frame

Line A

25mm

Line A

Fold to Door Edge

25 mm

Lock Chassis

Handle

Black Markings

Outside Cylinder

Inside Cylinder

Beak

Cylinder Locator

Door

Tail Piece

Outer Pull

Screw

Latch Lever

Black Markings

Striker

Keeper

Fixing Screw

Jacking Screw

Adjacent

Door Frame

Line A

25mm

Line A

Fold to Door Edge

25 mm

00566-001_SLIDING DOOR LCK IKONIC DBL CYL 697460_697470_697480 - Instruction LEAFLET-V1.indd   1

16/08/13   9:57 AM

Reviews: