IHP BarcelonaLights36ZEN Installation And Operation Instructions Manual Download

Page: 1 / 40

LISTED

This is a Single-Sided fireplace with the option of converting it into a See-Through fireplace

P900861-00

- Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

- WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use

any phone in your building.

• Leave the building immediately.

• Immediately call your gas supplier from a neigh-

bor’s phone. Follow the gas supplier’s instruc-

tions.

• If you cannot reach your gas supplier, call the

fire department.

- Installation and service must be performed by

a qualified installer, service agency or the gas

supplier.

WARNING:
FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could

result in serious injury, death, or property damage.

AVERTISSEMENT:
RISQUED’INDENDIE OU D’EXPLOSION

Le non-respect Des avertissements de sécurité pourrait

d’entraîner des blessures graves, la mort ou des dom-

mages matériels.

- Ne pas entreposer ni utilizer d’essence ni d’autres vapeurs

ou liquides inflammables dans le voisinage de cet appareil

ou de tout autre appareil.

- QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:

• Ne pas tenter d’allumer d’appareil.

• Ne touchez à aucan interrupteur. Ne pas vous servir des

téléphones se trouvant dans le bâtiment où vous trouvez.

• Sortez immédiatement de bâtiment.

• Appelez immédiatement votre fournisseur de gaz depuis

un voisin. Suivez les instructions du fournisseur.

• Si vous ne pouvez rejoindre le fournisseur de gaz, appelez

le service des incindies.

- L’installation et l’entretien doivent être assurés par un

installateur ou un service d’entretien qualifié ou par le

fournisseur de gaz.

WHEN USED AS AN OUTDOOR APPLIANCE

DANGER

CARBON MONOXIDE WARNING

• This appliance can produce

carbon monoxide which has

no odor.

• Using it in an enclosed space

can kill you.

• Never use this appliance in

an enclosed space such as a

camper, tent, car or home.

WARNING: For Outdoor Use Only.

DANGER

IF YOU SMELL GAS:

1. Shut off gas to appliance.

2. Extinguish any open flame.

3. If odor continues, keep away from the appliance and

immediately call your gas supplier or fire depart-

ment.

WARNING: Do not store gasoline or other flammable vapors and liquids in the vicinity of this or any other appli-

ance. An LP-cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.

WARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage.

Read the installation, operating and maintenance instructions thoroughly before installing or servicing this equipment.

INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.

Installateur : Laissez cette notice avec l’appareil.
Consommateur : Conservez cette notice pour consultation ultérieure.

Installation and Operation Instructions

P/N 900861-00 REV. NC 10/2017

Report No. MH# 60069

Ce manuel est disponible en francais,

simplement en faire la demande. Numéro

de la pièce 900861-01.

OUTDOOR DECORATIVE GAS FIREPLACE

Models

BarcelonaLights36ZEN

VRE4636ZEN

BarcelonaLights48ZEN

VRE4648ZEN

BarcelonaLights60ZEN

VRE4660ZEN

BarcelonaLights72ZEN

VRE4672ZEN

INSTALLATION PRECAUTION: This fireplace requires a minimum

18-square inches (per side) of cross ventilation. Failure to provide

proper ventilation can void the warranty.

Summary of Contents for BarcelonaLights36ZEN









































Search results

Summary of Contents for BarcelonaLights36ZEN

Reviews:

Related manuals for BarcelonaLights36ZEN

Brands by name

Popular brands

IHP BarcelonaLights36ZEN, Installation And Operation Instructions Manual

Search results

Summary of Contents for BarcelonaLights36ZEN

Reviews:

Related manuals for BarcelonaLights36ZEN

Brands by name

Popular brands