INSTRUCTION SHEET
2009.10
LD6A Series
3
Mounting
2
Specifications
Confirm that the delivered product is what you have ordered. Read this instruction sheet to make
sure of correct operation. Make sure that the instruction sheet is kept by the end user.
SAFETY PRECAUTIONS
*4 When using a
□
30 mm frame, the LD6A body protrudes from the frame.
・
For Frame Mount
Use flexible conduit only, otherwise the waterproof
characteristic will be impaired.
Refer to the "Example of Flexible Conduit" shown below.
6
Wiring
1
Type
http://www.idec.com
・
Read the specifications described on this sheet to make sure that the operating conditions are correct.
・
Before designing the final equipment and powering up the LD6A Series, confirm the specifications
decribed on this sheet. If there is any uncertainty in the description, contact IDEC before powering up
the LD6A Series.
・
Do not disassemble, repair, or modify the LD6A Series, otherwise severe accidents may result, such as
electric shocks, damage, fire, or malfunction.
・
Make sure that the LD6A Series does not fall during transportation, installation, and operation, otherwise
damage may result.
・
Do not pull out or push in the cable of the LD6A Series, otherwise damage may result. Give a slack to
the cable while wiring.
・
Turn off the power to the LD6A Series before mounting, dismounting, wiring, and assembling the LED
unit. Make sure of correct wiring, otherwise electric shocks or fire may result.
・
All LD6A Series are manufactured under IDEC's rigorous quality control system, but users must add
failsafe provision to the control system using the LD6A Series in applications where heavy damage or
personal injury may be caused in case the LD6A Series should fail.
・
Apply a voltage within the rated value.
・
Do not apply an excessive force to the LD6A Series. Do not leave a damaged LD6A Series unattended
or use a damaged LD6A.
・
Make sure of the correct operating temperature, which is the temperature around the LD6A Series.
Otherwise internal temperature rise may result in damage.
・
Do not use or store the LD6A Series in a place subjected to vibrations and shocks.
・
Do not loosen screws, otherwise the protection characteristics will be impaired.
・
For use on a flat surface of a Type 1 enclosure.
・
Maximum surrounding air temperature rating 55ºC.
・
See the figure on the upper right for the installation of the LD6A series.
・
For details on mounting holes, see Mounting Hole Layout.
LD6A-5WZQB-RYGSWC
Lens Color
Blank: Normal
C: Clear
Rated Voltage
Rated Insulation Voltage
LED Rated Current
Power Consumption
Applicable Standard
Operating Temperature *1
Operating Humidity
Storage Temperature
Operating Atomosphere
Operating Location
Overvoltage Category
Impulse Withstand Voltage (Uimp)
Insulation Resistance
Dielectric Strength
Vibration Resistance
(operating extremes)
Shock Resistance
Life *2
Degree of Protection
Flashing Cycle
Sound Pressure (at 1m)
Buzzer Cycle
Buzzer Power Consumption
Buzzer Inrush Current
24V AC/DC Class 2
60V
Red, Yellow: 25 mA
Green, Blue: 30 mA
Pure White: 20 mA
Red, Yellow: 0.6W
Green, Blue: 0.75W
Pure White: 0.5W
UL 508, CSA C22.2 No.14
IEC60947-5-1, EN60947-5-1, JIS C 8201-5-1
-25 ºC to +55 ºC (no freezing)
45 % to 85 % (no condensation)
-40 ºC to +75 ºC (no freezing)
Free from corrosive gases
Indoor use only
Ⅲ
(IEC 60664-1)
800V (IEC 60947-1 / JIS C8201-1)
100 M
Ω
minimum (500V DC megger)
1000V AC, 1 minute (between live and dead parts)
10 to 55 Hz, amplitude 0.5 mm
147 m/s
2
, 6 shocks each in 6 directions
30,000 hours
(until the brightness reduces to 50% the initial value when lit at
complete direct current of the rated voltage in 25 ºC environment)
IP65:Continuous Lighting
IP54:Continuous Lighting, Flashing, Buzzer
Pole Mount (with L-shaped bracket)-without L-shaped bracket
IP23
：
Pole Mount (with L-shaped bracket)-with L-shaped bracket
(
IEC 60529)
approx. 105 cycles per minute (1.75Hz)
70
〜
90 dB
（
3.3kHz
）
Buzzer 1: approx. 700 cycles per minute
Buzzer 2: approx. 35 cycles per minute
110mA
250mA max.(DC), 400mA max.(AC)
B-1229-1(0)
Illumination
R: Red
Y: Yellow
S: Blue
G: Green
W: Pure White
Body Color
B: Dark Gray
W: Light Gray
Rated Voltage
Q: 24V AC/DC
Tiers
1: 1 tier
2: 2 tiers
3: 3 tiers
4: 4 tiers
5: 5 tiers
Installation
G: Frame Mount
W: Wall Mount
D: Direct Mount
P: Pole Mount
(with stand)
K:Pole Mount
(with L-shaped bracket)
*1 The highest temperature is limited to 50 ºC when all tiers are lit continuously in the following combinations:
Two or more tiers including blue and green (Example: Red-Green-Blue, Green-Green-Red)
Four or five tiers (Example: Red-Yellow-Green-Pure White, Red-Yellow-Blue-Green-Pure White)
*2 Note that the durability of the LED is greatly attected by the operating conditions.
Note that the durability of the LED and Buzzer is greatly affected by the operating conditions.
・
The pole mount type can be installed in four ways.
The recommended mounting method is described below.
・
Recommended tightening torque: 2.6 to 2.7 N
・
m
①
Make four tapped holes in the mounting panel, and mount the bracket and gasket using four
screws (M4 x 20).
Recommended tightening torque: 1.6 to 1.7 N
・
m
②
Mount the LD6A to the bracket using four screws (M4 x 8).
Recommended tightening torque: 1.6 to 1.7 N
・
m
①I
nsert two frame nuts in the frame, and attach the bracket using two M5 screws.
Recommended tightening torque: 2.6 to 2.7 N
・
m
②
Mount the LD6A to the bracket using four M4 screws.
Recommended tightening torque: 1.6 to
1
.7 N
・
m
*3 See below for typical examples of Frames and Nuts.
Consult the manufacturer for the installation method of the frame nut.
●
Direct Mount
●
Wall Mount
●
Frame Mount
●
Pole Mount
Frame Size
□
30 mm *4
□
40 mm
Manufacturer
SUS Corporation
SUS
Corporation
Frame
SFF-302
SFF-402
Frame Nut
SFB-001
SFB-4B5
SFB-101
SFB-008
SFB-4A5
SFB-108
Conduit hole Size
M20
Fitting
AL16/M20/A/BL
Conduit
PAFS16BL
Manufacturer
ADAPTAFLEX
Pole Stand
4-M5 Mounting Hole
(recommended)
3-M4 Mounting Hole
4-M4 Mounting Hole
4-M5 Mounting Hole
・
Connect the wires as shown below. Incorrect wiring may damage the internal circuit.
・
Connect the wires to external contacts as needed for the number of tiers.
・
When using four tiers or less, insulate the unused wires.
・
Connect an appropriate fuse to the power line as shown in the figure below.
・
Use a UL listed external fuse holder.
・
Use a Class 2 power supply only.
・
When using the same color for two or more tiers, only one wire is used to light all tiers of the same color.
Determine the contact capacity in consideration of the LED rated current.
・
Do not apply voltage to flashing (brown) lines.
・
Do not connect flashing (brown) lines with power lines. The internal circuit may be damaged.
・
Do not turn on the continuous lighting and flashing contacts simultaneously. Use separate outside contacts.
・
When operating several continuous lighting, flashing, buzzer type units simultaneously, use separate outside
contacts.
・
When using buzzers 1 and 2 simultaneously, use separate outside contacts for continuous lighting and buzzer
type units respectively.
Wiring Diagram
NPN Transistor Operation
Supplied Parts
(Direct Mount)
M5 Screw
: 4
Spring Washer(M5) : 4
Flat Washer (M5) : 4
Nut (M5)
: 4
O-Ring
: 4
Gasket
: 1
Supplied Parts
(Pole Mount)
M5 Screw
: 4
Spring Washer (M5) : 4
Flat Washer (M5)
: 4
Nut (M5)
: 4
O-Ring
: 4
Gasket
: 1
Supplied Parts
(Wall Mount)
M4 Screw (l=20)
: 4
M4 Screw (l=8)
: 4
Flat Washer (M4) : 8
Spring Washer (M4): 8
Nut (M4)
: 4
Bracket
: 1
Gasket
: 1
Supplied Parts
(Frame Mount)
M4 Screw
: 4
Spring Washer : 4
Flat Washer
: 4
M5 Screw
: 2
Spring Washer : 2
Flat Washer
: 2
Bracket
: 1
Panel
Nut
Gasket
Braket
Flat Washer
Spring Washer
M4 Screw (l=20)
M4 Screw (l=8), Spring Washer, Flat Washer
①
②
Frame *3
Frame Nut *3
Bracket
Flat Washer
Spring Washer
M5 Screw
M4 Screw, Spring Washer, Flat Washer
・
Example of Flexible Conduit
・
Examples of recommended frames and frame nuts
・
Recommended tightening torque: 2.6 to 2.7 N
・
m
In this operation instruction sheet, safety precautions are categorized in order of importance to
Warning and Caution :
Caution notices are used where inattention might cause personal injury or damage to equipment.
Warning notices are used to emphasize that improper operation may cause severe personal
injury or death.
Power
supply
(24V AC / DC)
Fuse
1A
Power supply wire: Yellow
LED Pure White: White wire
LED Green: Green wire
LED Blue: Blue wire
LED Yellow: Orange wire
LED Red: Red wire
Blue
Green
Yellow
Red
Pure White
External
Contacts
Power
supply
(24V DC)
Fuse
1A
Power supply wire: Yellow
LED Pure White: White wire
LED Green: Green wire
LED Blue: Blue wire
LED Yellow: Orange wire
LED Red: Red wire
(-)
(+)
Pure White
Blue
Green
Yellow
Red
NPN
Transistor
PNP Transistor Operation
7
Precautions for Disposal
・
Direct Mount
・
Pole Mount
(with stand)
・
Wall Mount
・
Frame Mount
Tiers
1
2
3
4
5
Direct Mount
（
L3
）
98
128
158
188
218
（
L4
）
408
438
468
498
528
Wall Mount
（
L2
）
156
186
216
246
276
Frame Mount
（
L1
）
156
186
216
246
276
・
Dispose of the LD6A Series as an industrial waste.
M5 Screw
Spring Washer
Flat Washer
O-Ring
Base
Gasket
Nut
Panel
M5 Screw
O-Ring
Pole Stand
Gasket
Panel
Flat Washer
Spring Washer
Nut
Function
Blank :Continuous Lighting
Z
:Continuous Lighting, Flashing, Buzzer
●
Pole Mount (with stand)
・
Installing without L-shaped bracket
Remove the bushing, hexagonal nut (M22), plain
washer, and L-shaped bracket from the pole. Install
in order of plain washer, hexagonal nut (M22), and
bushing as shown in the figure at the right.
・
Recommended tightening torque
（
M10
）
: 10 to 11 N
・
m
・
Recommended tightening torque
（
M22
）
: 25 to 26 N
・
m
・
The parts marked with * are not supplied and should be
prepared by the user.
with L-shaped bracket
without L-shaped bracket
Hexagon head bolts*
（
M10
）
Flat Washer*
Nut*
（
M10
）
Spring Washer*
5
Sound pressure adjustment (Continuous Lighting, Flashing, Buzzer)
・
The sound pressure adjustment lever may be damaged if it is forcibly moved.
Move the sound pressure lever to the right and left to adjust the sound pressure.
The sound pressure is at maximum when the lever is set to the right.
(See figure at the right)
Sound pressure
adjustment lever
MIN
●
In order to make the buzzer sound more effective, face the unit to the front.
(Continuous Lighting, Flashing, Buzzer)
3
5
2‑
φ
11
φ
22
+1
0
4
Assembling the LED Units
・
Tighten the screws to the recommended tightening torque. The LED unit may
be damaged if the screw is loose during operation.
・
Do not touch the metal tabs of the LED unit. When a hand touches the metal tabs, static electricity may
damage the LED elements inside.
・
Use a maximum of 5 tiers.
・
Use an appropriate screw depending on the number of tiers. (optional)
・
Note the correct orientation when assembling the LED units.
・
Do not remove the packing from the LED unit. Waterproof characteristics will be impaired.
・
Turn off the power.
・
Remove the cap. Insert a flat screwdriver into the slot.
Use a screwdriver 1-mm thick and 7-mm wide maximum.
・
Pull out the cap by hand.
・
Loosen the screw in center.
・
Rearrange the LED units.
・
When assembling the LED unit, make sure to a lign the recess of the cap
with the recess of the LED unit.
Otherwise, damage may result.
・
Screw tightening torque
: 0.4 to 0.5 N
・ｍ
・
Mount the LD6A light on a flat surface not subjected to vibrations.
・
Do not mount the LD6A light upside-down or horizontally.
・
Do not leave the LD6A unit without a cap or unassembled.
・
Install the supplied gasket, otherwise waterproof characteristic is
impaired.
・
Mount the LD6A light on a flat surface, otherwise waterproof
characteristic is impaired.
・
Do not apply any chemicals which may corrode the plastic material.
・
Deburr the wiring holes.
・
Do not loosen the screws for which tightening torque is not specified.
・
If the LD6A light is subjected to strong vibrations, the hexagon
socket set screws may become loose. Apply screw lock paint.
See the figure at right.
2-M4 holes for hexagon socket set screws
(recommended tightening torque: 1.1 to 1.2 N
・
m)
Cap
LED Unit
Recess
Recess
Recess
Recess
Screwdriver Slot
①
②
③
●
Mounting Hole Layout (Dimensions in mm)
4-
φ
5.5
φ
15
φ
73
4-
φ
4.5
φ
73
90
°
φ
15
4-
φ
5.5
120
°
12
0
°
φ
40
3-
φ
4.5
φ
15
φ
54
φ
15
φ
15
φ
54
4-
φ
5.5
90
°
φ
15
4-
φ
4.5
46
23
16
2-M
5
44
.0
Direct Mount
Frame Mount
Wall Mount
Pole Mount
(Recommended)
Wiring hole
Wiring hole
Wiring hole
Wiring hole
Wiring hole
Wiring hole
↓
Front
↓
Front
*3 See below for typical examples of Frames and Nuts.
Consult the manufacturer for the installation method of the frame nut.
Frame *3
Frame Nut *3
Bracket
Flat Washer
Spring Washer
M5 Screw
Frame Size
□
30 mm *4
□
40 mm
Manufacturer
SUS Corporation
SUS
Corporation
Frame
SFF-302
SFF-402
Conduit hole
Size
M20
Fitting
AL16/M20/A/BL
Conduit
PAFS16BL
Manufacturer
ADAPTAFLEX
2-M
5
Frame Mount
●Mount
Hole (Dimensions in mm)
M4 Screw, Spring Washer, Flat Washer
①
②
・
Example of Flexible Conduit
・
Examples of recommended frames and frame nuts
Fitting
Conduit
Conduit hole
M20 x P1.6
①
②
Fitting
Conduit
Conduit hole
M20 x P1.5
Rated current
1A
Wire Color
LED Unit Color - Red
LED Unit Color - Yellow
LED Unit Color - Blue
LED Unit Color - Green
LED Unit Color - Pure White
Power supply wire
Wire Color
Red
Orange
Blue
Green
White
Yellow
Wire size
：
AWG22
・寸法一覧表
[単位
mm]
段数
1
2
3
4
5
直取付けタイプ
（L3）
170
200
230
260
290
円形台座付（L4）
408
438
468
498
528
壁取付けタイプ
（L2）
228
258
288
318
348
フレーム取付けタイプ
（L1）
228
258
288
318
348
ポール取付けタイプ
Ｌ形金具付（Ｌ５）
444
474
504
534
564
・寸法一覧表
[単位
mm]
段数
1
2
3
4
5
直取付けタイプ
（L3）
170
200
230
260
290
円形台座付（L4）
408
438
468
498
528
壁取付けタイプ
（L2）
228
258
288
318
348
フレーム取付けタイプ
（L1）
228
258
288
318
348
ポール取付けタイプ
Ｌ形金具付（Ｌ５）
444
474
504
534
564
・寸法一覧表
[単位
mm]
段数
1
2
3
4
5
直取付けタイプ
（L3）
170
200
230
260
290
円形台座付（L4）
408
438
468
498
528
壁取付けタイプ
（L2）
228
258
288
318
348
フレーム取付けタイプ
（L1）
228
258
288
318
348
ポール取付けタイプ
Ｌ形金具付（Ｌ５）
444
474
504
534
564
・
Continuous Lighting
6
5
5
2
.4
40
60
4
0
L1
9
8
0
2
5
1
7
.4
1
2
.6
60
40
5
3
.4
4
0
2
5
1
7
.4
1
2
.6
L2
980
6
5
60
4
0
φ7
0
2
5
1
7
.4
1
2
.6
L3
1
0
4
0
60
4
0
φ
9
4
2
5
1
7
.4
1
2
.6
L4
7
3
0
60
4
0
2
5
1
7
.4
1
2
.6
60
7
3
0
3
1
8
0
L5
80
40
・
Continuous Lighting, Flashing, Buzzer
5
2
.4
40
60
4
0
2
5
1
7
.4
1
2
.6
L1
9
0
0
6
5
60
40
5
3
.4
4
0
2
5
1
7
.4
1
2
.6
L2
6
5
900
60
4
0
φ7
0
2
5
1
7
.4
1
2
.6
L3
9
6
0
60
4
0
φ
9
4
2
5
1
7
.4
1
2
.6
L4
6
5
0
2
5
1
7
.4
1
2
.6
60
80
40
6
5
0
3
1
8
0
L5
60
4
0
・
Pole Mount
(with L-shaped bracket)
・
Direct Mount
・
Wall Mount
・
Frame Mount
・
Dimensions
・
Dimensions
（
L5
）
372
402
432
462
492
Pole Mount
Tiers
1
2
3
4
5
Direct Mount
（
L3
）
170
200
230
260
290
（
L4
）
480
510
540
570
600
Wall Mount
（
L2
）
228
258
288
318
348
Frame Mount
（
L1
）
228
258
288
318
348
（
L5
）
444
474
504
534
564
Pole Mount
Hexagon head
bolts
（
M22
）
Flat Washer
Bushing
Pole Mount (with L-shaped bracket)
with L-shaped bracket
without L-shaped bracket
Buzzer2: Light Blue
Buzzer1: Purple
LED Pure White: White wire
LED Green: Green wire
External Contacts
Continuous Lighting
Fuse 1A
Power supply
（
AC/DC 24V
）
Flashing COM: Brown
Power supply wire: Yellow
Blue
Green
Yellow
Red
Pure White
LED Blue: Blue wire
LED Yellow: Orange wire
LED Red: Red wire
External Contacts
Flashing
Power supply wire: Gray
Continuous Lighting, Flashing, Buzzer
LED Unit Color - Red
LED Unit Color - Yellow
LED Unit Color - Blue
LED Unit Color - Green
LED Unit Color - Pure White
Buzzer1
Buzzer2
Flashing
Power supply wire
Power supply wire
Wire size
：
AWG22
Wire Color
Red
Orange
Blue
Green
White
Purple
Light Blue
Brown
Gray
Yellow
・
Pole Mount
(with stand)
・
Pole Mount
(with L-shaped bracket)
NPN Transistor
Continuous Lighting
(+)
(‑)
Blue
Green
Yellow
Red
Pure White
Buzzer2: Light Blue
Buzzer1: Purple
LED Pure White: White wire
LED Green: Green wire
LED Blue: Blue wire
LED Yellow: Orange wire
LED Red: Red wire
Flashing COM: Brown
Power supply wire: Yellow
Power supply wire: Gray
Fuse 1A
Power supply
（
DC 24V
）
NPN Transistor
Flashing
Blue
Green
Yellow
Red
Pure White
Buzzer2: Light Blue
Buzzer1: Purple
LED Pure White: White wire
LED Green: Green wire
LED Blue: Blue wire
LED Yellow: Orange wire
LED Red: Red wire
Flashing COM: Brown
Power supply wire: Yellow
Power supply wire: Gray
(+)
(‑)
Fuse 1A
Power supply
（
DC 24V
）
PNP Transistor
Continuous Lighting
PNP Transistor
Flashing
MAX
Power
supply
(24V DC)
Fu
se
1A
(-)
(+)
Pure White
Blue
Green
Yellow
Red
PNP
Transistor
Power supply wire: Yellow
LED Pure White: White wire
LED Green: Green wire
LED Blue: Blue wire
LED Yellow: Orange wire
LED Red: Red wire
Packing
Hexagon head
bolts
（
M22
）
Fuse
7
Dimensions
Contact Capacity
for AC
(per one tire)
Contact Capacity
for DC/
Transistor Rating
(per one tire)
Current Capacity
Dielectric Strength
Dielectric Strength
Leakage Current
Current Capacity
100 mA minimum
AC 35V minimum
35V minimum
0.1 mA maximum
100 mA minimum
Rated Contact for Continuous Lighting
Contact Capacity
for AC
(per one sound)
Contact Capacity
for DC/
Transistor Rating
(per one sound)
Current Capacity
Dielectric Strength
Dielectric Strength
Leakage Current
Current Capacity
400 mA minimum
AC 35V minimum
35V minimum
0.1 mA maximum
300 mA minimum
Rated Contact for Buzzer
