background image

 

 

Engineering Manual for

 

 

 

 

AXS Series S40/S40i Keypad

 

 
 
 
 
S40/S40i Engineering Manual               

Page 1 of 8 

www.storm-interface.com

              

Rev 2.3 May  2016   

                                 © Copyright Storm Interface. 2015. All rights reserved

 

 

 

AXS SERIES S40 iCLASS SE

®

 PIN-Contactless Reader:  This integrated keypad and contactless reader is rated for 

continuous outdoor use in exposed, unsupervised locations. Featuring genuine HID

®

 iCLASS SE

®

, Seos

®

, contactless 

technology, this access control keypad offers enhanced security by dual factor authentication. Authorized access 

through a secured door or barrier can be gained by entry of a valid PIN and/or presentation of an authorized 13.56 

MHz contactless card, token or Seos

®

 device 

This manual covers the S40 and S40i, and is available from www.storm-interface.com/downloads. Each individual 

product includes a printed datasheet with just the essential information for installation

           

Contents 

 

 

 

 

 

 

 

 

 

 

Product Range and Accessories/Options  

Supported Credentials  

Installation / Wiring Connections  

Fitting the Keypad 

Wiegand Format / Configuration 

Specifications/Regulatory 

 

Whilst every effort is made to ensure details are correct at time of print, specifications are subject to change without notice.                                           
 

HID 

®

, Seos

®

 

and iCLASS SE

®

 

are trademarks of HID Global Corporation / ASSA ABLOY AB.

 

Storm, Storm Interface and Storm AXS are trademarks of Keymat Technology Ltd. 
 
Storm Interface products include technology protected by international patent and design registration.    
Storm Interface is an ISO9001 registered company.  Storm is a trading name of Keymat Technology Ltd 

Summary of Contents for AXS S40









Reviews: