Titan XP90 Quick Start Guide
Installation
• To install your new Titan, you will need a 115V, 60Hz, 3-Prong GFI outlet with a 15 amp time
delay fuse or circuit breaker.
• The area where the unit will be installed should be sealed with a vapor barrier. Additionally, if it
is a crawlspace, all vents and openings must be sealed.
• Be sure to route drain line to a suitable drain. The line must flow to drain without any loops or
kinks.
Operation
Turning the Unit On/Off
• To turn the dehumidifier on, press the power button
You will hear two beeps as the machine starts to run.
• Once running, the light will illuminate red.
• To turn the unit off, press the power button again.
You will hear a single beep as the machine begins the
shut down process. Keep in mind that there is a one
minute fan delay after shut down.
Adjusting the Settings
Humidity Level
• To adjust the humidity level, use the up and down arrow button until the desired level is
display on the screen . The dehumidifier can be set anywhere between 35-95%.
• Creating a desired humidity set point means that when the indoor humidity is lower the set
point, the machine will stop automatically. Conversely, when the indoor humidity is higher than
the set level, the unit will operate.
Continuous Mode
• If you need your Titan to run constantly, you can use Continuous Mode. To switch into
Continuous mode, press either the up or down arrow button until you hear an audible
beep. Next, press button the up and down keys at the same time. At this point, the
light should illuminate green on the display board to indicate the unit has been
successfully switched to Continuous Mode.
• Once in continuous mode, the dehumidifier will run constantly regardless of the humidity level
until you turn the unit off or switch back to normal humidistat operation. If you would like to
change to humidistat operation, simply press the up and down arrows simultaneously.
Compressor Indicator
• The compressor indicator will illuminate red on the display board to show that
compressor operation has been initiated and unit is currently warming up. Wait a few minutes
and the compressor will begin to run. Once running, the compressor indicator will switch to
green.
HORIZON-DEHUMIDIFIERS
HORIZON-DEHUMIDIFIERS
Do not install dehumidifier in a corrosive environment. Some liquid vapor
barriers dry via“solvent evaporation”. Insure barrier is completely dry and area is
thoroughly ventilated before installing dehumidifier.
WARNING!
1)
Place dehumidifier on level surface
If after unit is positioned
If the unit is handled in such a manner that the compressor did not remain in the upright position,
place on level surface and wait a minimum of 2 hours before turning the unit“on”.
NOTE: XG90 dehumidifier can’t sit directly on floor unless the unit is feeding directly into a sump
next to it. Elevation is required to allow gravity flow of condensate water to drain.
WARNING!
2)
Drain Line
3) Plug unit into 15 amp grounded outlet.
Key functions
1. Power Key
indicator light must be on to show unit is plugged in and has power to it. Press the on/off
button, and the machine will start running (Two Beeps). Press this key again, the machine will stop
running (Single Beep). The display will read room humidity levels except while you’re adjusting the
setpoint humidity level. NOTE: When unit is turned off, the fan will run for 1 minute prior to shutting off.
2. Increase Humidity button
Press this button to set indoor humidity , according to this sequence: 60%, 65%, 70%, 75%.
When the indoor humidity is lower than the set humidity, the machine will stop automatically. When
indoor humidity is higher than setpoint, the unit will operate.
3. Decrease Humidity button
Press this button to set indoor humidity
, according to this sequence: 60%, 55%, 50%,45%,
40%. When the indoor humidity lower than set humidity, the machine will stop working automatically.
When the indoor humidity is higher than setpoint, unit will operate.
4. Continuous Mode button
Press either the increase or decrease humidity buttons. Once you hear an audible beep, press both
buttons simultaneously to put the dehumidifier into“continuous”mode.”
The indicator light on will illuminate green indicating the unit is in continuous mode.
The unit will continue to operate regardless of humidity level until the user manually changes the
humidity setting, turns the unit off or presses
again and the unit will return to normal
humidistat control operation.
NOTE: The humidity levels shown on the unit display are approximate only. (+/- 5%)
.
Drain line should be routed to a suitable drain on outside. Drain line must flow down to a drain
without any loops, dips or valleys.
Recommended Drain Option – Transition to PVC Pipe
Cut a piece of ¾”OD PVC approximately 6”long and insert into a ¾”elbow then attach to a ¾”
OD length of PVC to drain. (Note: Keep the length of PVC drain pipe to a minimum).
Insert the open end of the tubing into the ¾”pipe so that it does not extend into the elbow fitting.
For proper flow, a minimum downward slope of 1”per 10’run is required. (Note: If a proper downward
angle is not possible then it is recommended to use a Titan XP90 with the integrated condensate pump
or utilize an external condensate pump provided by others.)
Support the PVC tubing so that it maintains a smooth downward flow to drain.
Test drain before leaving.
Drain Tube – 12 inches Long. 12 mm OD.
88
Power
Dehumidifiers
Dehumidifiers
Comp
Cont.
Defrost
Power
88
88
Cont.
Defrost
HORIZON-DEHUMIDIFIERS
HORIZON-DEHUMIDIFIERS
Do not install dehumidifier in a corrosive environment. Some liquid vapor
barriers dry via“solvent evaporation”. Insure barrier is completely dry and area is
thoroughly ventilated before installing dehumidifier.
WARNING!
1)
Place dehumidifier on level surface
If after unit is positioned
If the unit is handled in such a manner that the compressor did not remain in the upright position,
place on level surface and wait a minimum of 2 hours before turning the unit“on”.
NOTE: XG90 dehumidifier can’t sit directly on floor unless the unit is feeding directly into a sump
next to it. Elevation is required to allow gravity flow of condensate water to drain.
WARNING!
2)
Drain Line
3) Plug unit into 15 amp grounded outlet.
Key functions
1. Power Key
indicator light must be on to show unit is plugged in and has power to it. Press the on/off
button, and the machine will start running (Two Beeps). Press this key again, the machine will stop
running (Single Beep). The display will read room humidity levels except while you’re adjusting the
setpoint humidity level. NOTE: When unit is turned off, the fan will run for 1 minute prior to shutting off.
2. Increase Humidity button
Press this button to set indoor humidity , according to this sequence: 60%, 65%, 70%, 75%.
When the indoor humidity is lower than the set humidity, the machine will stop automatically. When
indoor humidity is higher than setpoint, the unit will operate.
3. Decrease Humidity button
Press this button to set indoor humidity
, according to this sequence: 60%, 55%, 50%,45%,
40%. When the indoor humidity lower than set humidity, the machine will stop working automatically.
When the indoor humidity is higher than setpoint, unit will operate.
4. Continuous Mode button
Press either the increase or decrease humidity buttons. Once you hear an audible beep, press both
buttons simultaneously to put the dehumidifier into“continuous”mode.”
The indicator light on will illuminate green indicating the unit is in continuous mode.
The unit will continue to operate regardless of humidity level until the user manually changes the
humidity setting, turns the unit off or presses
again and the unit will return to normal
humidistat control operation.
NOTE: The humidity levels shown on the unit display are approximate only. (+/- 5%)
.
Drain line should be routed to a suitable drain on outside. Drain line must flow down to a drain
without any loops, dips or valleys.
Recommended Drain Option – Transition to PVC Pipe
Cut a piece of ¾”OD PVC approximately 6”long and insert into a ¾”elbow then attach to a ¾”
OD length of PVC to drain. (Note: Keep the length of PVC drain pipe to a minimum).
Insert the open end of the tubing into the ¾”pipe so that it does not extend into the elbow fitting.
For proper flow, a minimum downward slope of 1”per 10’run is required. (Note: If a proper downward
angle is not possible then it is recommended to use a Titan XP90 with the integrated condensate pump
or utilize an external condensate pump provided by others.)
Support the PVC tubing so that it maintains a smooth downward flow to drain.
Test drain before leaving.
Drain Tube – 12 inches Long. 12 mm OD.
88
Power
Dehumidifiers
Dehumidifiers
Comp
Cont.
Defrost
Power
88
88
Cont.
Defrost
HORIZON-DEHUMIDIFIERS
HORIZON-DEHUMIDIFIERS
Do not install dehumidifier in a corrosive environment. Some liquid vapor
barriers dry via“solvent evaporation”. Insure barrier is completely dry and area is
thoroughly ventilated before installing dehumidifier.
WARNING!
1)
Place dehumidifier on level surface
If after unit is positioned
If the unit is handled in such a manner that the compressor did not remain in the upright position,
place on level surface and wait a minimum of 2 hours before turning the unit“on”.
NOTE: XG90 dehumidifier can’t sit directly on floor unless the unit is feeding directly into a sump
next to it. Elevation is required to allow gravity flow of condensate water to drain.
WARNING!
2)
Drain Line
3) Plug unit into 15 amp grounded outlet.
Key functions
1. Power Key
indicator light must be on to show unit is plugged in and has power to it. Press the on/off
button, and the machine will start running (Two Beeps). Press this key again, the machine will stop
running (Single Beep). The display will read room humidity levels except while you’re adjusting the
setpoint humidity level. NOTE: When unit is turned off, the fan will run for 1 minute prior to shutting off.
2. Increase Humidity button
Press this button to set indoor humidity , according to this sequence: 60%, 65%, 70%, 75%.
When the indoor humidity is lower than the set humidity, the machine will stop automatically. When
indoor humidity is higher than setpoint, the unit will operate.
3. Decrease Humidity button
Press this button to set indoor humidity
, according to this sequence: 60%, 55%, 50%,45%,
40%. When the indoor humidity lower than set humidity, the machine will stop working automatically.
When the indoor humidity is higher than setpoint, unit will operate.
4. Continuous Mode button
Press either the increase or decrease humidity buttons. Once you hear an audible beep, press both
buttons simultaneously to put the dehumidifier into“continuous”mode.”
The indicator light on will illuminate green indicating the unit is in continuous mode.
The unit will continue to operate regardless of humidity level until the user manually changes the
humidity setting, turns the unit off or presses
again and the unit will return to normal
humidistat control operation.
NOTE: The humidity levels shown on the unit display are approximate only. (+/- 5%)
.
Drain line should be routed to a suitable drain on outside. Drain line must flow down to a drain
without any loops, dips or valleys.
Recommended Drain Option – Transition to PVC Pipe
Cut a piece of ¾”OD PVC approximately 6”long and insert into a ¾”elbow then attach to a ¾”
OD length of PVC to drain. (Note: Keep the length of PVC drain pipe to a minimum).
Insert the open end of the tubing into the ¾”pipe so that it does not extend into the elbow fitting.
For proper flow, a minimum downward slope of 1”per 10’run is required. (Note: If a proper downward
angle is not possible then it is recommended to use a Titan XP90 with the integrated condensate pump
or utilize an external condensate pump provided by others.)
Support the PVC tubing so that it maintains a smooth downward flow to drain.
Test drain before leaving.
Drain Tube – 12 inches Long. 12 mm OD.
88
Power
Dehumidifiers
Dehumidifiers
Comp
Cont.
Defrost
Power
88
88
Cont.
Defrost
HORIZON-DEHUMIDIFIERS
HORIZON-DEHUMIDIFIERS
Do not install dehumidifier in a corrosive environment. Some liquid vapor
barriers dry via“solvent evaporation”. Insure barrier is completely dry and area is
thoroughly ventilated before installing dehumidifier.
WARNING!
1)
Place dehumidifier on level surface
If after unit is positioned
If the unit is handled in such a manner that the compressor did not remain in the upright position,
place on level surface and wait a minimum of 2 hours before turning the unit“on”.
NOTE: XG90 dehumidifier can’t sit directly on floor unless the unit is feeding directly into a sump
next to it. Elevation is required to allow gravity flow of condensate water to drain.
WARNING!
2)
Drain Line
3) Plug unit into 15 amp grounded outlet.
Key functions
1. Power Key
indicator light must be on to show unit is plugged in and has power to it. Press the on/off
button, and the machine will start running (Two Beeps). Press this key again, the machine will stop
running (Single Beep). The display will read room humidity levels except while you’re adjusting the
setpoint humidity level. NOTE: When unit is turned off, the fan will run for 1 minute prior to shutting off.
2. Increase Humidity button
Press this button to set indoor humidity , according to this sequence: 60%, 65%, 70%, 75%.
When the indoor humidity is lower than the set humidity, the machine will stop automatically. When
indoor humidity is higher than setpoint, the unit will operate.
3. Decrease Humidity button
Press this button to set indoor humidity
, according to this sequence: 60%, 55%, 50%,45%,
40%. When the indoor humidity lower than set humidity, the machine will stop working automatically.
When the indoor humidity is higher than setpoint, unit will operate.
4. Continuous Mode button
Press either the increase or decrease humidity buttons. Once you hear an audible beep, press both
buttons simultaneously to put the dehumidifier into“continuous”mode.”
The indicator light on will illuminate green indicating the unit is in continuous mode.
The unit will continue to operate regardless of humidity level until the user manually changes the
humidity setting, turns the unit off or presses
again and the unit will return to normal
humidistat control operation.
NOTE: The humidity levels shown on the unit display are approximate only. (+/- 5%)
.
Drain line should be routed to a suitable drain on outside. Drain line must flow down to a drain
without any loops, dips or valleys.
Recommended Drain Option – Transition to PVC Pipe
Cut a piece of ¾”OD PVC approximately 6”long and insert into a ¾”elbow then attach to a ¾”
OD length of PVC to drain. (Note: Keep the length of PVC drain pipe to a minimum).
Insert the open end of the tubing into the ¾”pipe so that it does not extend into the elbow fitting.
For proper flow, a minimum downward slope of 1”per 10’run is required. (Note: If a proper downward
angle is not possible then it is recommended to use a Titan XP90 with the integrated condensate pump
or utilize an external condensate pump provided by others.)
Support the PVC tubing so that it maintains a smooth downward flow to drain.
Test drain before leaving.
Drain Tube – 12 inches Long. 12 mm OD.
88
Power
Dehumidifiers
Dehumidifiers
Comp
Cont.
Defrost
Power
88
88
Cont.
Defrost
HORIZON-DEHUMIDIFIERS
HORIZON-DEHUMIDIFIERS
Do not install dehumidifier in a corrosive environment. Some liquid vapor
barriers dry via“solvent evaporation”. Insure barrier is completely dry and area is
thoroughly ventilated before installing dehumidifier.
WARNING!
1)
Place dehumidifier on level surface
If after unit is positioned
If the unit is handled in such a manner that the compressor did not remain in the upright position,
place on level surface and wait a minimum of 2 hours before turning the unit“on”.
NOTE: XG90 dehumidifier can’t sit directly on floor unless the unit is feeding directly into a sump
next to it. Elevation is required to allow gravity flow of condensate water to drain.
WARNING!
2)
Drain Line
3) Plug unit into 15 amp grounded outlet.
Key functions
1. Power Key
indicator light must be on to show unit is plugged in and has power to it. Press the on/off
button, and the machine will start running (Two Beeps). Press this key again, the machine will stop
running (Single Beep). The display will read room humidity levels except while you’re adjusting the
setpoint humidity level. NOTE: When unit is turned off, the fan will run for 1 minute prior to shutting off.
2. Increase Humidity button
Press this button to set indoor humidity , according to this sequence: 60%, 65%, 70%, 75%.
When the indoor humidity is lower than the set humidity, the machine will stop automatically. When
indoor humidity is higher than setpoint, the unit will operate.
3. Decrease Humidity button
Press this button to set indoor humidity
, according to this sequence: 60%, 55%, 50%,45%,
40%. When the indoor humidity lower than set humidity, the machine will stop working automatically.
When the indoor humidity is higher than setpoint, unit will operate.
4. Continuous Mode button
Press either the increase or decrease humidity buttons. Once you hear an audible beep, press both
buttons simultaneously to put the dehumidifier into“continuous”mode.”
The indicator light on will illuminate green indicating the unit is in continuous mode.
The unit will continue to operate regardless of humidity level until the user manually changes the
humidity setting, turns the unit off or presses
again and the unit will return to normal
humidistat control operation.
NOTE: The humidity levels shown on the unit display are approximate only. (+/- 5%)
.
Drain line should be routed to a suitable drain on outside. Drain line must flow down to a drain
without any loops, dips or valleys.
Recommended Drain Option – Transition to PVC Pipe
Cut a piece of ¾”OD PVC approximately 6”long and insert into a ¾”elbow then attach to a ¾”
OD length of PVC to drain. (Note: Keep the length of PVC drain pipe to a minimum).
Insert the open end of the tubing into the ¾”pipe so that it does not extend into the elbow fitting.
For proper flow, a minimum downward slope of 1”per 10’run is required. (Note: If a proper downward
angle is not possible then it is recommended to use a Titan XP90 with the integrated condensate pump
or utilize an external condensate pump provided by others.)
Support the PVC tubing so that it maintains a smooth downward flow to drain.
Test drain before leaving.
Drain Tube – 12 inches Long. 12 mm OD.
88
Power
Dehumidifiers
Dehumidifiers
Comp
Cont.
Defrost
Power
88
88
Cont.
Defrost
HORIZON-DEHUMIDIFIERS
HORIZON-DEHUMIDIFIERS
Do not install dehumidifier in a corrosive environment. Some liquid vapor
barriers dry via“solvent evaporation”. Insure barrier is completely dry and area is
thoroughly ventilated before installing dehumidifier.
WARNING!
1)
Place dehumidifier on level surface
If after unit is positioned
If the unit is handled in such a manner that the compressor did not remain in the upright position,
place on level surface and wait a minimum of 2 hours before turning the unit“on”.
NOTE: XG90 dehumidifier can’t sit directly on floor unless the unit is feeding directly into a sump
next to it. Elevation is required to allow gravity flow of condensate water to drain.
WARNING!
2)
Drain Line
3) Plug unit into 15 amp grounded outlet.
Key functions
1. Power Key
indicator light must be on to show unit is plugged in and has power to it. Press the on/off
button, and the machine will start running (Two Beeps). Press this key again, the machine will stop
running (Single Beep). The display will read room humidity levels except while you’re adjusting the
setpoint humidity level. NOTE: When unit is turned off, the fan will run for 1 minute prior to shutting off.
2. Increase Humidity button
Press this button to set indoor humidity , according to this sequence: 60%, 65%, 70%, 75%.
When the indoor humidity is lower than the set humidity, the machine will stop automatically. When
indoor humidity is higher than setpoint, the unit will operate.
3. Decrease Humidity button
Press this button to set indoor humidity
, according to this sequence: 60%, 55%, 50%,45%,
40%. When the indoor humidity lower than set humidity, the machine will stop working automatically.
When the indoor humidity is higher than setpoint, unit will operate.
4. Continuous Mode button
Press either the increase or decrease humidity buttons. Once you hear an audible beep, press both
buttons simultaneously to put the dehumidifier into“continuous”mode.”
The indicator light on will illuminate green indicating the unit is in continuous mode.
The unit will continue to operate regardless of humidity level until the user manually changes the
humidity setting, turns the unit off or presses
again and the unit will return to normal
humidistat control operation.
NOTE: The humidity levels shown on the unit display are approximate only. (+/- 5%)
.
Drain line should be routed to a suitable drain on outside. Drain line must flow down to a drain
without any loops, dips or valleys.
Recommended Drain Option – Transition to PVC Pipe
Cut a piece of ¾”OD PVC approximately 6”long and insert into a ¾”elbow then attach to a ¾”
OD length of PVC to drain. (Note: Keep the length of PVC drain pipe to a minimum).
Insert the open end of the tubing into the ¾”pipe so that it does not extend into the elbow fitting.
For proper flow, a minimum downward slope of 1”per 10’run is required. (Note: If a proper downward
angle is not possible then it is recommended to use a Titan XP90 with the integrated condensate pump
or utilize an external condensate pump provided by others.)
Support the PVC tubing so that it maintains a smooth downward flow to drain.
Test drain before leaving.
Drain Tube – 12 inches Long. 12 mm OD.
88
Power
Dehumidifiers
Dehumidifiers
Comp
Cont.
Defrost
Power
88
88
Cont.
Defrost
HORIZON-DEHUMIDIFIERS
HORIZON-DEHUMIDIFIERS
Do not install dehumidifier in a corrosive environment. Some liquid vapor
barriers dry via“solvent evaporation”. Insure barrier is completely dry and area is
thoroughly ventilated before installing dehumidifier.
WARNING!
1)
Place dehumidifier on level surface
If after unit is positioned
If the unit is handled in such a manner that the compressor did not remain in the upright position,
place on level surface and wait a minimum of 2 hours before turning the unit“on”.
NOTE: XG90 dehumidifier can’t sit directly on floor unless the unit is feeding directly into a sump
next to it. Elevation is required to allow gravity flow of condensate water to drain.
WARNING!
2)
Drain Line
3) Plug unit into 15 amp grounded outlet.
Key functions
1. Power Key
indicator light must be on to show unit is plugged in and has power to it. Press the on/off
button, and the machine will start running (Two Beeps). Press this key again, the machine will stop
running (Single Beep). The display will read room humidity levels except while you’re adjusting the
setpoint humidity level. NOTE: When unit is turned off, the fan will run for 1 minute prior to shutting off.
2. Increase Humidity button
Press this button to set indoor humidity , according to this sequence: 60%, 65%, 70%, 75%.
When the indoor humidity is lower than the set humidity, the machine will stop automatically. When
indoor humidity is higher than setpoint, the unit will operate.
3. Decrease Humidity button
Press this button to set indoor humidity
, according to this sequence: 60%, 55%, 50%,45%,
40%. When the indoor humidity lower than set humidity, the machine will stop working automatically.
When the indoor humidity is higher than setpoint, unit will operate.
4. Continuous Mode button
Press either the increase or decrease humidity buttons. Once you hear an audible beep, press both
buttons simultaneously to put the dehumidifier into“continuous”mode.”
The indicator light on will illuminate green indicating the unit is in continuous mode.
The unit will continue to operate regardless of humidity level until the user manually changes the
humidity setting, turns the unit off or presses
again and the unit will return to normal
humidistat control operation.
NOTE: The humidity levels shown on the unit display are approximate only. (+/- 5%)
.
Drain line should be routed to a suitable drain on outside. Drain line must flow down to a drain
without any loops, dips or valleys.
Recommended Drain Option – Transition to PVC Pipe
Cut a piece of ¾”OD PVC approximately 6”long and insert into a ¾”elbow then attach to a ¾”
OD length of PVC to drain. (Note: Keep the length of PVC drain pipe to a minimum).
Insert the open end of the tubing into the ¾”pipe so that it does not extend into the elbow fitting.
For proper flow, a minimum downward slope of 1”per 10’run is required. (Note: If a proper downward
angle is not possible then it is recommended to use a Titan XP90 with the integrated condensate pump
or utilize an external condensate pump provided by others.)
Support the PVC tubing so that it maintains a smooth downward flow to drain.
Test drain before leaving.
Drain Tube – 12 inches Long. 12 mm OD.
88
Power
Dehumidifiers
Dehumidifiers
Comp
Cont.
Defrost
Power
88
88
Cont.
Defrost
HORIZON-DEHUMIDIFIERS
HORIZON-DEHUMIDIFIERS
Do not install dehumidifier in a corrosive environment. Some liquid vapor
barriers dry via“solvent evaporation”. Insure barrier is completely dry and area is
thoroughly ventilated before installing dehumidifier.
WARNING!
1)
Place dehumidifier on level surface
If after unit is positioned
If the unit is handled in such a manner that the compressor did not remain in the upright position,
place on level surface and wait a minimum of 2 hours before turning the unit“on”.
NOTE: XG90 dehumidifier can’t sit directly on floor unless the unit is feeding directly into a sump
next to it. Elevation is required to allow gravity flow of condensate water to drain.
WARNING!
2)
Drain Line
3) Plug unit into 15 amp grounded outlet.
Key functions
1. Power Key
indicator light must be on to show unit is plugged in and has power to it. Press the on/off
button, and the machine will start running (Two Beeps). Press this key again, the machine will stop
running (Single Beep). The display will read room humidity levels except while you’re adjusting the
setpoint humidity level. NOTE: When unit is turned off, the fan will run for 1 minute prior to shutting off.
2. Increase Humidity button
Press this button to set indoor humidity , according to this sequence: 60%, 65%, 70%, 75%.
When the indoor humidity is lower than the set humidity, the machine will stop automatically. When
indoor humidity is higher than setpoint, the unit will operate.
3. Decrease Humidity button
Press this button to set indoor humidity
, according to this sequence: 60%, 55%, 50%,45%,
40%. When the indoor humidity lower than set humidity, the machine will stop working automatically.
When the indoor humidity is higher than setpoint, unit will operate.
4. Continuous Mode button
Press either the increase or decrease humidity buttons. Once you hear an audible beep, press both
buttons simultaneously to put the dehumidifier into“continuous”mode.”
The indicator light on will illuminate green indicating the unit is in continuous mode.
The unit will continue to operate regardless of humidity level until the user manually changes the
humidity setting, turns the unit off or presses
again and the unit will return to normal
humidistat control operation.
NOTE: The humidity levels shown on the unit display are approximate only. (+/- 5%)
.
Drain line should be routed to a suitable drain on outside. Drain line must flow down to a drain
without any loops, dips or valleys.
Recommended Drain Option – Transition to PVC Pipe
Cut a piece of ¾”OD PVC approximately 6”long and insert into a ¾”elbow then attach to a ¾”
OD length of PVC to drain. (Note: Keep the length of PVC drain pipe to a minimum).
Insert the open end of the tubing into the ¾”pipe so that it does not extend into the elbow fitting.
For proper flow, a minimum downward slope of 1”per 10’run is required. (Note: If a proper downward
angle is not possible then it is recommended to use a Titan XP90 with the integrated condensate pump
or utilize an external condensate pump provided by others.)
Support the PVC tubing so that it maintains a smooth downward flow to drain.
Test drain before leaving.
Drain Tube – 12 inches Long. 12 mm OD.
88
Power
Dehumidifiers
Dehumidifiers
Comp
Cont.
Defrost
Power
88
88
Cont.
Defrost
HORIZON-DEHUMIDIFIERS
HORIZON-DEHUMIDIFIERS
Do not install dehumidifier in a corrosive environment. Some liquid vapor
barriers dry via“solvent evaporation”. Insure barrier is completely dry and area is
thoroughly ventilated before installing dehumidifier.
WARNING!
1)
Place dehumidifier on level surface
If after unit is positioned
If the unit is handled in such a manner that the compressor did not remain in the upright position,
place on level surface and wait a minimum of 2 hours before turning the unit“on”.
NOTE: XG90 dehumidifier can’t sit directly on floor unless the unit is feeding directly into a sump
next to it. Elevation is required to allow gravity flow of condensate water to drain.
WARNING!
2)
Drain Line
3) Plug unit into 15 amp grounded outlet.
Key functions
1. Power Key
indicator light must be on to show unit is plugged in and has power to it. Press the on/off
button, and the machine will start running (Two Beeps). Press this key again, the machine will stop
running (Single Beep). The display will read room humidity levels except while you’re adjusting the
setpoint humidity level. NOTE: When unit is turned off, the fan will run for 1 minute prior to shutting off.
2. Increase Humidity button
Press this button to set indoor humidity , according to this sequence: 60%, 65%, 70%, 75%.
When the indoor humidity is lower than the set humidity, the machine will stop automatically. When
indoor humidity is higher than setpoint, the unit will operate.
3. Decrease Humidity button
Press this button to set indoor humidity
, according to this sequence: 60%, 55%, 50%,45%,
40%. When the indoor humidity lower than set humidity, the machine will stop working automatically.
When the indoor humidity is higher than setpoint, unit will operate.
4. Continuous Mode button
Press either the increase or decrease humidity buttons. Once you hear an audible beep, press both
buttons simultaneously to put the dehumidifier into“continuous”mode.”
The indicator light on will illuminate green indicating the unit is in continuous mode.
The unit will continue to operate regardless of humidity level until the user manually changes the
humidity setting, turns the unit off or presses
again and the unit will return to normal
humidistat control operation.
NOTE: The humidity levels shown on the unit display are approximate only. (+/- 5%)
.
Drain line should be routed to a suitable drain on outside. Drain line must flow down to a drain
without any loops, dips or valleys.
Recommended Drain Option – Transition to PVC Pipe
Cut a piece of ¾”OD PVC approximately 6”long and insert into a ¾”elbow then attach to a ¾”
OD length of PVC to drain. (Note: Keep the length of PVC drain pipe to a minimum).
Insert the open end of the tubing into the ¾”pipe so that it does not extend into the elbow fitting.
For proper flow, a minimum downward slope of 1”per 10’run is required. (Note: If a proper downward
angle is not possible then it is recommended to use a Titan XP90 with the integrated condensate pump
or utilize an external condensate pump provided by others.)
Support the PVC tubing so that it maintains a smooth downward flow to drain.
Test drain before leaving.
Drain Tube – 12 inches Long. 12 mm OD.
88
Power
Dehumidifiers
Dehumidifiers
Comp
Cont.
Defrost
Power
88
88
Cont.
Defrost
HORIZON-DEHUMIDIFIERS
HORIZON-DEHUMIDIFIERS
Do not install dehumidifier in a corrosive environment. Some liquid vapor
barriers dry via“solvent evaporation”. Insure barrier is completely dry and area is
thoroughly ventilated before installing dehumidifier.
WARNING!
1)
Place dehumidifier on level surface
If after unit is positioned
If the unit is handled in such a manner that the compressor did not remain in the upright position,
place on level surface and wait a minimum of 2 hours before turning the unit“on”.
NOTE: XG90 dehumidifier can’t sit directly on floor unless the unit is feeding directly into a sump
next to it. Elevation is required to allow gravity flow of condensate water to drain.
WARNING!
2)
Drain Line
3) Plug unit into 15 amp grounded outlet.
Key functions
1. Power Key
indicator light must be on to show unit is plugged in and has power to it. Press the on/off
button, and the machine will start running (Two Beeps). Press this key again, the machine will stop
running (Single Beep). The display will read room humidity levels except while you’re adjusting the
setpoint humidity level. NOTE: When unit is turned off, the fan will run for 1 minute prior to shutting off.
2. Increase Humidity button
Press this button to set indoor humidity , according to this sequence: 60%, 65%, 70%, 75%.
When the indoor humidity is lower than the set humidity, the machine will stop automatically. When
indoor humidity is higher than setpoint, the unit will operate.
3. Decrease Humidity button
Press this button to set indoor humidity
, according to this sequence: 60%, 55%, 50%,45%,
40%. When the indoor humidity lower than set humidity, the machine will stop working automatically.
When the indoor humidity is higher than setpoint, unit will operate.
4. Continuous Mode button
Press either the increase or decrease humidity buttons. Once you hear an audible beep, press both
buttons simultaneously to put the dehumidifier into“continuous”mode.”
The indicator light on will illuminate green indicating the unit is in continuous mode.
The unit will continue to operate regardless of humidity level until the user manually changes the
humidity setting, turns the unit off or presses
again and the unit will return to normal
humidistat control operation.
NOTE: The humidity levels shown on the unit display are approximate only. (+/- 5%)
.
Drain line should be routed to a suitable drain on outside. Drain line must flow down to a drain
without any loops, dips or valleys.
Recommended Drain Option – Transition to PVC Pipe
Cut a piece of ¾”OD PVC approximately 6”long and insert into a ¾”elbow then attach to a ¾”
OD length of PVC to drain. (Note: Keep the length of PVC drain pipe to a minimum).
Insert the open end of the tubing into the ¾”pipe so that it does not extend into the elbow fitting.
For proper flow, a minimum downward slope of 1”per 10’run is required. (Note: If a proper downward
angle is not possible then it is recommended to use a Titan XP90 with the integrated condensate pump
or utilize an external condensate pump provided by others.)
Support the PVC tubing so that it maintains a smooth downward flow to drain.
Test drain before leaving.
Drain Tube – 12 inches Long. 12 mm OD.
88
Power
Dehumidifiers
Dehumidifiers
Comp
Cont.
Defrost
Power
88
88
Cont.
Defrost
HORIZON-DEHUMIDIFIERS
HORIZON-DEHUMIDIFIERS
Do not install dehumidifier in a corrosive environment. Some liquid vapor
barriers dry via“solvent evaporation”. Insure barrier is completely dry and area is
thoroughly ventilated before installing dehumidifier.
WARNING!
1)
Place dehumidifier on level surface
If after unit is positioned
If the unit is handled in such a manner that the compressor did not remain in the upright position,
place on level surface and wait a minimum of 2 hours before turning the unit“on”.
NOTE: XG90 dehumidifier can’t sit directly on floor unless the unit is feeding directly into a sump
next to it. Elevation is required to allow gravity flow of condensate water to drain.
WARNING!
2)
Drain Line
3) Plug unit into 15 amp grounded outlet.
Key functions
1. Power Key
indicator light must be on to show unit is plugged in and has power to it. Press the on/off
button, and the machine will start running (Two Beeps). Press this key again, the machine will stop
running (Single Beep). The display will read room humidity levels except while you’re adjusting the
setpoint humidity level. NOTE: When unit is turned off, the fan will run for 1 minute prior to shutting off.
2. Increase Humidity button
Press this button to set indoor humidity , according to this sequence: 60%, 65%, 70%, 75%.
When the indoor humidity is lower than the set humidity, the machine will stop automatically. When
indoor humidity is higher than setpoint, the unit will operate.
3. Decrease Humidity button
Press this button to set indoor humidity
, according to this sequence: 60%, 55%, 50%,45%,
40%. When the indoor humidity lower than set humidity, the machine will stop working automatically.
When the indoor humidity is higher than setpoint, unit will operate.
4. Continuous Mode button
Press either the increase or decrease humidity buttons. Once you hear an audible beep, press both
buttons simultaneously to put the dehumidifier into“continuous”mode.”
The indicator light on will illuminate green indicating the unit is in continuous mode.
The unit will continue to operate regardless of humidity level until the user manually changes the
humidity setting, turns the unit off or presses
again and the unit will return to normal
humidistat control operation.
NOTE: The humidity levels shown on the unit display are approximate only. (+/- 5%)
.
Drain line should be routed to a suitable drain on outside. Drain line must flow down to a drain
without any loops, dips or valleys.
Recommended Drain Option – Transition to PVC Pipe
Cut a piece of ¾”OD PVC approximately 6”long and insert into a ¾”elbow then attach to a ¾”
OD length of PVC to drain. (Note: Keep the length of PVC drain pipe to a minimum).
Insert the open end of the tubing into the ¾”pipe so that it does not extend into the elbow fitting.
For proper flow, a minimum downward slope of 1”per 10’run is required. (Note: If a proper downward
angle is not possible then it is recommended to use a Titan XP90 with the integrated condensate pump
or utilize an external condensate pump provided by others.)
Support the PVC tubing so that it maintains a smooth downward flow to drain.
Test drain before leaving.
Drain Tube – 12 inches Long. 12 mm OD.
88
Power
Dehumidifiers
Dehumidifiers
Comp
Cont.
Defrost
Power
88
88
Cont.
Defrost
HORIZON-DEHUMIDIFIERS
HORIZON-DEHUMIDIFIERS
Do not install dehumidifier in a corrosive environment. Some liquid vapor
barriers dry via“solvent evaporation”. Insure barrier is completely dry and area is
thoroughly ventilated before installing dehumidifier.
WARNING!
1)
Place dehumidifier on level surface
If after unit is positioned
If the unit is handled in such a manner that the compressor did not remain in the upright position,
place on level surface and wait a minimum of 2 hours before turning the unit“on”.
NOTE: XG90 dehumidifier can’t sit directly on floor unless the unit is feeding directly into a sump
next to it. Elevation is required to allow gravity flow of condensate water to drain.
WARNING!
2)
Drain Line
3) Plug unit into 15 amp grounded outlet.
Key functions
1. Power Key
indicator light must be on to show unit is plugged in and has power to it. Press the on/off
button, and the machine will start running (Two Beeps). Press this key again, the machine will stop
running (Single Beep). The display will read room humidity levels except while you’re adjusting the
setpoint humidity level. NOTE: When unit is turned off, the fan will run for 1 minute prior to shutting off.
2. Increase Humidity button
Press this button to set indoor humidity , according to this sequence: 60%, 65%, 70%, 75%.
When the indoor humidity is lower than the set humidity, the machine will stop automatically. When
indoor humidity is higher than setpoint, the unit will operate.
3. Decrease Humidity button
Press this button to set indoor humidity
, according to this sequence: 60%, 55%, 50%,45%,
40%. When the indoor humidity lower than set humidity, the machine will stop working automatically.
When the indoor humidity is higher than setpoint, unit will operate.
4. Continuous Mode button
Press either the increase or decrease humidity buttons. Once you hear an audible beep, press both
buttons simultaneously to put the dehumidifier into“continuous”mode.”
The indicator light on will illuminate green indicating the unit is in continuous mode.
The unit will continue to operate regardless of humidity level until the user manually changes the
humidity setting, turns the unit off or presses
again and the unit will return to normal
humidistat control operation.
NOTE: The humidity levels shown on the unit display are approximate only. (+/- 5%)
.
Drain line should be routed to a suitable drain on outside. Drain line must flow down to a drain
without any loops, dips or valleys.
Recommended Drain Option – Transition to PVC Pipe
Cut a piece of ¾”OD PVC approximately 6”long and insert into a ¾”elbow then attach to a ¾”
OD length of PVC to drain. (Note: Keep the length of PVC drain pipe to a minimum).
Insert the open end of the tubing into the ¾”pipe so that it does not extend into the elbow fitting.
For proper flow, a minimum downward slope of 1”per 10’run is required. (Note: If a proper downward
angle is not possible then it is recommended to use a Titan XP90 with the integrated condensate pump
or utilize an external condensate pump provided by others.)
Support the PVC tubing so that it maintains a smooth downward flow to drain.
Test drain before leaving.
Drain Tube – 12 inches Long. 12 mm OD.
88
Power
Dehumidifiers
Dehumidifiers
Comp
Cont.
Defrost
Power
88
88
Cont.
Defrost
HORIZON-DEHUMIDIFIERS
HORIZON-DEHUMIDIFIERS
Indicator Lights
LED humidity display
This LED indicator shows two functions
1. When the power supply is on, the Led indicator shows indoor humidity
.
2. When you set humidity, the LED indicator shows the set humidity
.
88
Power Indicator Light
This indicates the unit has been plugged in ready to operate. Please make sure this light is “off”
prior to performing any service on this unit.
Continuous Mode Light
This indicates unit has been set in the“Continuous”operation mode.The light will illuminate a green
color.
Auto defrost
When the Auto Defrost light glows red, it means the unit is in the defrost mode and is clearing the
evaporator coil of any ice buildup.
Humidity Display Lights
These lights have 2 functions:
1. When the power is on, it shows the indoor humidity level;
2. When you set humidity value, it shows the selected humidity setpoint. After a brief delay, the
display will go back to the actual indoor humidity level.
The“Comp”indicator light on
red indicates the compressor operation has been initiated. If
the compressor doesn’t immediately, just wait several minutes for its time delay protection to be
completed and the compressor with energize.
The“Comp”indicator
light
on green indicates the compressor has been in working status
※
※
Horizon Titan XG 90
※
Front View
Unit Cover
Control panel
Air Outlet Grille
Discharge End Cap
Power cord
Remote control
※
Back View
Unit Cover
Drain Hose Quick
Handle
Power cord
Inlet End Cap
Air Intlet Grille
※
※
Operating Instructions
1. Start the machine
As soon as the machine is powered on for the first time, the buzzer will buzz. Adjust the humidity
level to the desired setpoint (typically 50-55%). Press to start the machine.
2. Stop machine
Press and the machine will stop. Note the fan will operate for 1 minute after the unit has
been turned off.
DO NOT unplug the power cord directly to force the machine stop working directly.
3. Water Drainage
During normal operation, the Titan XG90 will automatically drain by the force of gravity. If you
want to move or store the machine, wait at least 10 minutes to allow the machine to completely defrost
and then lean machine gently towards drain to insure the unit is completely drained.
Cont.
Defrost
Cont.
Defrost
Comp
88
Comp
HORIZON-DEHUMIDIFIERS
HORIZON-DEHUMIDIFIERS
Indicator Lights
LED humidity display
This LED indicator shows two functions
1. When the power supply is on, the Led indicator shows indoor humidity
.
2. When you set humidity, the LED indicator shows the set humidity
.
88
Power Indicator Light
This indicates the unit has been plugged in ready to operate. Please make sure this light is “off”
prior to performing any service on this unit.
Continuous Mode Light
This indicates unit has been set in the“Continuous”operation mode.The light will illuminate a green
color.
Auto defrost
When the Auto Defrost light glows red, it means the unit is in the defrost mode and is clearing the
evaporator coil of any ice buildup.
Humidity Display Lights
These lights have 2 functions:
1. When the power is on, it shows the indoor humidity level;
2. When you set humidity value, it shows the selected humidity setpoint. After a brief delay, the
display will go back to the actual indoor humidity level.
The“Comp”indicator light on
red indicates the compressor operation has been initiated. If
the compressor doesn’t immediately, just wait several minutes for its time delay protection to be
completed and the compressor with energize.
The“Comp”indicator
light
on green indicates the compressor has been in working status
※
※
Horizon Titan XG 90
※
Front View
Unit Cover
Control panel
Air Outlet Grille
Discharge End Cap
Power cord
Remote control
※
Back View
Unit Cover
Drain Hose Quick
Handle
Power cord
Inlet End Cap
Air Intlet Grille
※
※
Operating Instructions
1. Start the machine
As soon as the machine is powered on for the first time, the buzzer will buzz. Adjust the humidity
level to the desired setpoint (typically 50-55%). Press to start the machine.
2. Stop machine
Press and the machine will stop. Note the fan will operate for 1 minute after the unit has
been turned off.
DO NOT unplug the power cord directly to force the machine stop working directly.
3. Water Drainage
During normal operation, the Titan XG90 will automatically drain by the force of gravity. If you
want to move or store the machine, wait at least 10 minutes to allow the machine to completely defrost
and then lean machine gently towards drain to insure the unit is completely drained.
Cont.
Defrost
Cont.
Defrost
Comp
88
Comp
HORIZON-DEHUMIDIFIERS
HORIZON-DEHUMIDIFIERS
Do not install dehumidifier in a corrosive environment. Some liquid vapor
barriers dry via“solvent evaporation”. Insure barrier is completely dry and area is
thoroughly ventilated before installing dehumidifier.
WARNING!
1)
Place dehumidifier on level surface
If after unit is positioned
If the unit is handled in such a manner that the compressor did not remain in the upright position,
place on level surface and wait a minimum of 2 hours before turning the unit“on”.
NOTE: XG90 dehumidifier can’t sit directly on floor unless the unit is feeding directly into a sump
next to it. Elevation is required to allow gravity flow of condensate water to drain.
WARNING!
2)
Drain Line
3) Plug unit into 15 amp grounded outlet.
Key functions
1. Power Key
indicator light must be on to show unit is plugged in and has power to it. Press the on/off
button, and the machine will start running (Two Beeps). Press this key again, the machine will stop
running (Single Beep). The display will read room humidity levels except while you’re adjusting the
setpoint humidity level. NOTE: When unit is turned off, the fan will run for 1 minute prior to shutting off.
2. Increase Humidity button
Press this button to set indoor humidity , according to this sequence: 60%, 65%, 70%, 75%.
When the indoor humidity is lower than the set humidity, the machine will stop automatically. When
indoor humidity is higher than setpoint, the unit will operate.
3. Decrease Humidity button
Press this button to set indoor humidity
, according to this sequence: 60%, 55%, 50%,45%,
40%. When the indoor humidity lower than set humidity, the machine will stop working automatically.
When the indoor humidity is higher than setpoint, unit will operate.
4. Continuous Mode button
Press either the increase or decrease humidity buttons. Once you hear an audible beep, press both
buttons simultaneously to put the dehumidifier into“continuous”mode.”
The indicator light on will illuminate green indicating the unit is in continuous mode.
The unit will continue to operate regardless of humidity level until the user manually changes the
humidity setting, turns the unit off or presses
again and the unit will return to normal
humidistat control operation.
NOTE: The humidity levels shown on the unit display are approximate only. (+/- 5%)
.
Drain line should be routed to a suitable drain on outside. Drain line must flow down to a drain
without any loops, dips or valleys.
Recommended Drain Option – Transition to PVC Pipe
Cut a piece of ¾”OD PVC approximately 6”long and insert into a ¾”elbow then attach to a ¾”
OD length of PVC to drain. (Note: Keep the length of PVC drain pipe to a minimum).
Insert the open end of the tubing into the ¾”pipe so that it does not extend into the elbow fitting.
For proper flow, a minimum downward slope of 1”per 10’run is required. (Note: If a proper downward
angle is not possible then it is recommended to use a Titan XP90 with the integrated condensate pump
or utilize an external condensate pump provided by others.)
Support the PVC tubing so that it maintains a smooth downward flow to drain.
Test drain before leaving.
Drain Tube – 12 inches Long. 12 mm OD.
88
Power
Dehumidifiers
Dehumidifiers
Comp
Cont.
Defrost
Power
88
88
Cont.
Defrost
HORIZON-DEHUMIDIFIERS
HORIZON-DEHUMIDIFIERS
Do not install dehumidifier in a corrosive environment. Some liquid vapor
barriers dry via“solvent evaporation”. Insure barrier is completely dry and area is
thoroughly ventilated before installing dehumidifier.
WARNING!
1)
Place dehumidifier on level surface
If after unit is positioned
If the unit is handled in such a manner that the compressor did not remain in the upright position,
place on level surface and wait a minimum of 2 hours before turning the unit“on”.
NOTE: XG90 dehumidifier can’t sit directly on floor unless the unit is feeding directly into a sump
next to it. Elevation is required to allow gravity flow of condensate water to drain.
WARNING!
2)
Drain Line
3) Plug unit into 15 amp grounded outlet.
Key functions
1. Power Key
indicator light must be on to show unit is plugged in and has power to it. Press the on/off
button, and the machine will start running (Two Beeps). Press this key again, the machine will stop
running (Single Beep). The display will read room humidity levels except while you’re adjusting the
setpoint humidity level. NOTE: When unit is turned off, the fan will run for 1 minute prior to shutting off.
2. Increase Humidity button
Press this button to set indoor humidity , according to this sequence: 60%, 65%, 70%, 75%.
When the indoor humidity is lower than the set humidity, the machine will stop automatically. When
indoor humidity is higher than setpoint, the unit will operate.
3. Decrease Humidity button
Press this button to set indoor humidity
, according to this sequence: 60%, 55%, 50%,45%,
40%. When the indoor humidity lower than set humidity, the machine will stop working automatically.
When the indoor humidity is higher than setpoint, unit will operate.
4. Continuous Mode button
Press either the increase or decrease humidity buttons. Once you hear an audible beep, press both
buttons simultaneously to put the dehumidifier into“continuous”mode.”
The indicator light on will illuminate green indicating the unit is in continuous mode.
The unit will continue to operate regardless of humidity level until the user manually changes the
humidity setting, turns the unit off or presses
again and the unit will return to normal
humidistat control operation.
NOTE: The humidity levels shown on the unit display are approximate only. (+/- 5%)
.
Drain line should be routed to a suitable drain on outside. Drain line must flow down to a drain
without any loops, dips or valleys.
Recommended Drain Option – Transition to PVC Pipe
Cut a piece of ¾”OD PVC approximately 6”long and insert into a ¾”elbow then attach to a ¾”
OD length of PVC to drain. (Note: Keep the length of PVC drain pipe to a minimum).
Insert the open end of the tubing into the ¾”pipe so that it does not extend into the elbow fitting.
For proper flow, a minimum downward slope of 1”per 10’run is required. (Note: If a proper downward
angle is not possible then it is recommended to use a Titan XP90 with the integrated condensate pump
or utilize an external condensate pump provided by others.)
Support the PVC tubing so that it maintains a smooth downward flow to drain.
Test drain before leaving.
Drain Tube – 12 inches Long. 12 mm OD.
88
Power
Dehumidifiers
Dehumidifiers
Comp
Cont.
Defrost
Power
88
88
Cont.
Defrost
