Hitachi SJ2-CO Instruction Manual Download

Page: 1 / 35

INSTRUCTION MANUAL

Thank you for purchase of “SJ2-CO (CANopen Interface Option)”.

This manual explains about treatment of “SJ2-CO”. By reading this

manual and an instruction manual of inverter use practically for

installation, maintenance, and inspection. After reading this manual,

keep it handy for future reference.

Make sure to deliver this manual to the end user.

Table of Contents

Chapter1 Introduction 1

Chapter2 Mounting method of option

Chapter3 Wiring, Connecting 7

Chapter4 Setting 9

Chapter5 CANopen communication function 11

Chapter6 Countermeasure for abnormality

Chapter7 Communication Objects Lists 23

Chapter8

Specifications 30

Chapter9 Contact information 31

SJ200-2/L200-2 SERIES

SJ2-CO

(CANopen Interface Option)

N B6 5 4 X

Hitachi Inverter

After reading this manual, keep it at handy for future reference.

Summary of Contents for SJ2-CO




































Search results

Summary of Contents for SJ2-CO

Reviews:

Related manuals for SJ2-CO

Brands by name

Popular brands

Hitachi SJ2-CO, Instruction Manual

Search results

Summary of Contents for SJ2-CO

Reviews:

Related manuals for SJ2-CO

Brands by name

Popular brands