Safety information
Do not touch or contact the input/output terminals because they may cause electric shock.
DANGER
•Before you use, please read safety precautions carefully, and use this product properly.
• If you are concerned about serious accident due to the malfunction of products, please
install the external safety equipment
• To prevent defection or malfunction of this product, supply proper power voltage in
accordance with the rating.
• To prevent electric shock or devise malfunction of this product, do not supply the
power until the wiring is completed.
• Reassemble this product while the power is off. Otherwise, it may cause malfunction or
electric shock.
• If the user uses the product with methods other than specified by the manufacturer,
it will brings the bodily injuries or property damages.
• Due to the danger of electric shock, please use this product installed onto a panel
while an electric current is applied.
WARNING
• Before using the product you have purchased, please check out if it is exactly what you ordered.
• Do not use this product at any place with corrosive gas (especially noxious gas or
ammonia) or flammable gas.
• Do not use this product at any place with liquid, oil, medical substances, dust, salt or iron contents.
• Do not use this product at any place with excessive induction trouble, static electricity
or magnetic noise.
• Do not use this product at any place with possible thermal accumulation due to direct
sunlight or heat radiation.
• When the product gets wet, the inspection is essential because there is a danger of
an electric leakage or fire.
•Do not connect anything to the unused terminals.
•For DC types, please connect wires at the correct position after checking polarity of terminal.
•When product is disposed, treat as a industrial waste.
•Since a heat sink corner is sharp, it would lead to a serious injury.
• When electricity flows, desktop or heat sink's corner temperature would be high so
that it could lead people to suffer burns.
•When it is out of order, please separate SSR from head sink and change only SSR.
•This model has epoxy molding for the purpose of safety, reliability and extends of the life.
• When applying an electric current, SSR is heated more and more. So, it has more durable
at low heat sink temperature and ambient temperature.
CAUTION
Suffix code
Model
Code
Information
HSR-2SL
2-Phase Solid State Relay
Input Control Voltage D
4 - 32 V d.c.
Rated load current
25
25 A
40
40 A
Rated load voltage
2
90 - 264 V a.c. (Low voltage)
4
90 - 480 V a.c. (High voltage)
Operation method
Z
Zero Cross Switching (Standard product)
MC0701KE230807
28, Gilpa-ro 71beon-gil, Michuhol-gu, Incheon, Korea
TEL : +82-32-876-4697
http://www.hanyoungnux.com
HANYOUNGNUX CO.,LTD
HEAD OFFICE
Slim Type
HSR-2SL
2-Phase Solid State Relay
Thank you for purchasing HANYOUNG product.
Please check whether the product is the exactly same as you ordered.
Before using the product, please read this instruction manual carefully.
Please keep this manual where you can view at any time
INSTRUCTION MANUAL
DANGER indicates an imminently hazardous situation which, if
not avoided, will result in death or serious injury
WARNING indicates a potentially hazardous situation which, if
not avoided, could result in death or serious injury
CAUTION indicates a potentially hazardous situation which, if
not avoided, may result in minor or moderate injury
DANGER
WARNING
CAUTION
Before using the product, please read the safety information thoroughly and use it properly.
Alerts declared in the manual are classified to Danger, Warning and Caution by their criticality
Specification
Rated Voltage
5 - 24 V d.c.
Operating Voltage Range
4 - 32 V d.c.
Impedance
Less than 4 ㏀
Operation Voltage
More than 3 V d.c.
Reset Voltage
Less than 1.5 V d.c.
Input Current
Constant-current system : 10 ㎃ (±3)
Rated Voltage
24 V d.c.
Operating Voltage Range
20 - 26 V d.c.
Power consumption Max 25 ㎃, Max 40 ㎃ in case of Alarm output (Base on 24 V d.c.)
Collector pressure
30 V d.c. max
Maximum rated
through current
50 ㎃ max
Max. collector
power consumption
500 mW
Output type
Transistor open collector (Hi at detection of problem)
Response Time
1/2 Cycle + 1 ms max. (“R”type below 1 ms)
Insulating Resistance
500 V d.c., 100 ㏁ (Between the input / output and case)
Dielectric strength
2,500 V a.c. (For 1 min at 60 ㎐)
Vibration resistance
10 - 55 ㎐, Double amplitude : 1.5 ㎜, X,Y, and Z direction for 2 hours
Shock resistance
1,000 ㎨, X,Y,Z each axis 3 times
Storage Temperature
-30 ~ 90 ℃
Ambient Temperature
0 ~ 25 ℃ (But without frostiness)
Ambient Humidity
45 ~ 85 % R.H.
Pollution level grade
2 level pollution
Degree of protection
IP20
Usage
Resistive load / Inductive load
Accepted standard
IEC 62314
Certification
Weight (with box)
Approx. 1,000 g
Approx. 1,300 g
Detection
par
ts
Dimension
[Unit : mm]
Specification
Model
Low
HSR-2SLD252Z
HSR-2SLD402Z
High
HSR-2SLD254Z
HSR-2SLD404Z
Rated Load
Voltage
Low
90 - 264 V a.c.
High
90 - 480 V a.c.
Peak Voltage
(Non-repetition)
Low
600 V
High
1,200 V
Rated load current
25 A
40 A
Frequency
50/60 Hz (Dual usage)
Surge current
(8.3 ms No repetition)
Low
260 A
420 A
High
250 A
370 A
Leakage current
10 ㎃ max
Output ON voltage dropping
1.8 V (R.M.S) max
Rated impulse
withstand voltage
Low
4 ㎸
High
6 ㎸
LO
AD
INPUT
96.6
79.0
87.6
4.5
6.5
10.0
4.5
74.0
131.3
13.85
20.5
74.0
96.6
87.6
4.5
6.5
10.0
4.5
13.85
20.5
95.0
156.7
● HSR_2SLD 외형 및 패널 가공치수 (단위:mm)
● HSR_2SE 외형 및 패널 가공치수 (단위:mm)
110.0
147.0
110.0
74.0
99.1
41.0
140.1
50.0
133.0
6.5
8.0
● HSR_2SLD 404Z 외형 및 패널 가공치수 (단위:mm)
※ DIN Rail 사용불가
96.6
58.0
87.6
4.5
6.5
10.0
4.5
13.85
20.5
130.0
74.0
96.6
79.0
87.6
4.5
6.5
10.0
4.5
74.0
131.3
13.85
20.5
74.0
96.6
87.6
4.5
6.5
10.0
4.5
13.85
20.5
95.0
156.7
● HSR_2SLD 외형 및 패널 가공치수 (단위:mm)
● HSR_2SE 외형 및 패널 가공치수 (단위:mm)
110.0
147.0
110.0
74.0
99.1
41.0
140.1
50.0
133.0
6.5
8.0
● HSR_2SLD 404Z 외형 및 패널 가공치수 (단위:mm)
※ DIN Rail 사용불가
96.6
58.0
87.6
4.5
6.5
10.0
4.5
13.85
20.5
130.0
74.0
96.6
79.0
87.6
4.5
6.5
10.0
4.5
74.0
131.3
13.85
20.5
74.0
96.6
87.6
4.5
6.5
10.0
4.5
13.85
20.5
95.0
156.7
● HSR_2SLD 외형 및 패널 가공치수 (단위:mm)
● HSR_2SE 외형 및 패널 가공치수 (단위:mm)
110.0
147.0
110.0
74.0
99.1
41.0
140.1
50.0
133.0
6.5
8.0
● HSR_2SLD 404Z 외형 및 패널 가공치수 (단위:mm)
※ DIN Rail 사용불가
96.6
58.0
87.6
4.5
6.5
10.0
4.5
13.85
20.5
130.0
74.0
HSR-2SLD252Z, 254Z
HSR-2SLD402Z
HSR-2SLD404Z
