Feeney DesignRail LED 40W-DK Installation Instructions Manual Download | Manualshive

Page: 1 / 11

background image

1-800-888-2418 | www.feeneyinc.com

1

Rev: 10/21

Drivers are available in a variety of wa ages. In general a driver should not exceed more than 80% of its rated wa age. (Example:
60W Driver = 60 x 0.8 = 48W Max).

Building codes vary by loca on and jurisdic on. Consult all applicable codes before installing DesignRail® LED Ligh ng. DesignRail

®

LED Ligh ng may not be suitable for every applica on and it is the sole responsibility of the installer to ensure that DesignRail

®

LED

Ligh ng is used for its intended purpose.

WARNING: ELECTRIC SHOCK IS ALWAYS POSSIBLE WHEN WORKING WITH ELECTRICITY. THIS CAN CAUSE SERIOUS PERSONAL
INJURIES OR DEATH. ELECTRICAL SHORTS CAN ALSO CAUSE FIRES AND PROPERTY DAMAGE. ALWAYS MAKE SURE THE

ELECTRICAL OUTLET YOU ARE PLUGGING INTO IS GROUNDED.

DesignRail

®

24V LED Post Accent Light

Installa on Instruc ons

1
2
3
...
»

Summary of Contents for DesignRail LED 40W-DK












Reviews:

No comments

Related manuals for DesignRail LED 40W-DK

Brand: Tala Pages: 8

Adult Picnic Table

Brand: NBB Pages: 8

Brand: Qlightec Pages: 2

Kingston KIS12134

Brand: Gardiun Pages: 28

Glasgow KIS12992

Brand: Gardiun Pages: 26

Home Garden Pub

Brand: Fishers Woodscraft Pages: 8

Brand: Sunnydaze Decor Pages: 2

Brand: macc Pages: 4

Brand: Kozyard Pages: 23

Brand: Fantom Pages: 24

PRO CART ULTRA PCU800

Brand: Cambro Pages: 9

Brand: Ibiza Pages: 9

Brand: Facom Pages: 20

Brand: VONROC Pages: 24

Brand: A Little Lovely Company Pages: 2

Brand: Uniflame Pages: 12

Brand: Wacker Neuson Pages: 110

Brand: FLYSURFER Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands