background image

- 1 -

AS-220T

Staircase lighting timer 

with switch-off indication

Staircase lighting timer (time switch) is used to keep the lighting 

on in corridors, staircases or other places for a certain period of 

time, after which the lighting will be switched off automatically.

When activated by momentary (bell) switch the staircase lighting 

timer keeps the lighting switched on for the time set by the po-

tentiometer (from 0.5 to 10 minutes), after which the brightness 

of the lighting system is reduced to the level set by the potentio-

meter (from 25 % to 70 %) for 30 seconds.

Only after this time will the lighting be completely switched off 

(sudden darkness is avoided, there is time for safe access to the 

switch). During the reduced brightness the subsequent signal 

from the switch will switch the lighting back on to full brightness. 

The device can operate in on of two modes: with anti-lock on or 

off, and the choice is made by the installer during the installation 

(shorting the selection input to the phase voltage or leaving it 

unconnected).

Purpose

Functioning

F&F Filipowski sp. j.

Konstantynowska 79/81, 95-200 Pabianice, POLAND

phone/fax (+48 42) 215 23 83 / (+48 42) 227 09 71

www.fif.com.pl; e-mail: [email protected]

Do not dispose of this device in the trash along with other waste!  

According to 

the Law on Waste, electro coming from households free of charge and can give any 

amount to up to that end point of collec� on, as well as to store the occasion of the 

purchase of new equipment (in accordance with the principle of old-for-new, regard-

less of brand). Electro thrown in the trash or abandoned in nature, pose a threat to 

the environment and human health.

Summary of Contents for AS-220T









Reviews: