iRMMM=c~ãáäó
qbojfk^i=fkpq^ii^qflk=drfab
`ljmif^k`b
qbojfk^i=fkpq^ii^qflk=drfab
bèìáåçñ=m~óãÉåíë
9045 E. Pima Center Parkway, Suite 3, Scottsdale, Arizona 85258, USA | Tel: 480.551.7800 | Fax: 480.551.7811
© 2011-2014 Equinox Payments. All rights reserved. The Equinox logo is a trademark of Equinox Payments. All other products or services mentioned in this
document are trademarks, service marks, registered trademarks or registered service marks of their respective owners.
940660-001E Rev. B 08/14
The user is cautioned that changes or modifications to the device(s) identified in this manual unless expressly approved by the
party responsible for compliance could void the user’s authority to operate this device. This is a class A device. In a domestic
environment this device may cause radio interference in which case the user may be required to take adequate measures.
•
FCC Part 15 B - Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause undesired operation.
•
FCC ID: NVA00010
•
UL Listed
•
RoHS
•
PCI PTS 3.xx with SRED
iRMMM=c~ãáäó
klqf`bp
If a power supply was NOT shipped with the L5X00s terminal or if there is NOT an immediately available power supply to use with the
L5X00s, use the following when selecting and using a suitable power supply:
•
Must use Equinox P/N 870066-004, or
•
Must use a suitably safety Listed power supply, output rated 12-24Vdc 1A or greater and must be a certified Limited Power Source, marked LPS.
To Clean Screen: Apply distilled water or mild
glass cleaner onto a soft, lint free cloth and
gently wipe terminal screen.
To Clean Terminal: Apply distilled water or plastic-
safe cleaner onto a soft, lint free cloth and gently
wipe terminal.
N
Smart
Card
Reader
MSR Slot
Ports
(in the back)
Cleaning the Device
• Do NOT use industrial
strength or an abrasive
cleaner as it may
damage or scratch the
screen.
• Do NOT immerse device
in water (or liquid).
• Do NOT spray water or
cleaner into the MSR
slot, Smart Card Reader
or ports in the back.
N
Screen
t
^okfkd
W
Inserting a MicroSD Card
Power down and remove all power
from terminal before installing card.
Turn terminal over. Loosen two
retained screws on underside of ter-
minal and remove top cap or con-
tactless module. Card slot is
accessible once top cap or
contactless module is removed.
Insert card (gold connectors down) into
MicroSD slot (as shown). Push card in
until firmly seated in slot. Reinstall top
cap or contactless module. Tighten two
retained screws to secure the top cap
or module to terminal. Contact Equinox
for list of approved cards and format-
ting information.
O
Screws
MicroSD Slot
• When so powered, this device is intended to be connected only to Power over Ethernet (PoE) networks that are not routed to
the outside plant.
klqbW=
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accor-
dance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residen-
tial area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may
not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
(940660-001E)
Applicable to
L5200 and L5300
Applicable to
L5200 and L5300
N
MSR Slot
In
sp
ec
tin
g
Slo
ts
Closely, visually inspect the MSR
Slot for any foreign objects that
may obstruct, hamper or prevent
the sliding of your card thru the
MSR Reader.
If any foreign objects are found,
do NOT use and notify the appro-
priate person immediately for the
device may be compromised.
If no foregin objects exist, use the
device as normal.
O
Smart Card Reader Slot
Closely, visually inspect the Smart
Card Reader Slot for any foreign
objects that may obstruct, hamper
or prevent your smart card from
being read.
If any foreign objects are found,
do NOT use and notify the appro-
priate person immediately for the
device may be compromised.
If no foregin objects exist, use the
device as normal.
