INSTALLATION
NSTRUCTIONS
WARRANTY INFORMATION
This device is warranted to be free of material and workmanship defects for 2 years from the date of purchase. Original receipt
or proof of purchase from an authorized retailer must be presented upon warranty claim. ALL claims must be verified and
approved by
Enerwave
, Inc. Warranties from other
Enerwave
products may vary. This warranty is nontransferable and does
not cover normal wear and tear or any malfunction, failure, or defect resulting from misuse, abuse, neglect, alteration,
modification, or improper installation. To the fullest extent permitted by the applicable state law,
Enerwave
shall not be liable to
the purchaser or end user customer of
Enerwave
products for direct, indirect, incidental, or consequential damages even if
Enerwave
has been advised of the possibility of such damages.
Enerwave
’
s
total liability under this or any other warranty,
express or implied, is limited to repair, replacement or refund. Repair, replacement or refund are the sole and exclusive
remedies for breach of warranty or any other legal theory.
©
2016
Enerwave Home Automation ●
WWW.
ENERWAVEAUTOMATION
.COM
● CA, USA
Model:
ZW
N-RSM1-PLUS
Smart Single Relay Switch
Module
020
8
1600
4
3
-0
2
WARNING
:
Turn the POWER OFF at the circuit breaker before installing the
Relay
Read and understand these instructions before installing. This device is intended for installation in accordance with the National Electric Code and local regulations. It is recommended that a qualified electrician perform
s
this installation. Make sure to turn off the circuit breaker or fuse(s)
and make sure power is off before wiring the device.
Exercise extreme caution when using Z-Wave devices to control appliances. Operation of the Z-Wave device may be in a different room than the controlled appliance so an unintentional activation may occur if the wrong button on the
remote is pressed. Z-Wave devices can be automatically powered on by programmed events. Unattended or unintentional operation could result in hazardous conditions. Z-Wave enabled devices should never be used to supply power to, control or monitor medical and/or life support
equipment.
Use copper wires only.
•
Connect
the
BLACK wire on
the relay
to the HOT wire.
•
Connect
the
WHITE wire on
the relay
to the NEUTRAL wire.
•
Connect the Red wire on
the relay
to the LOAD wire.
•
Connect the ORANGE wire on the relay to one of the
terminal screws on the wall switch.
•
Connect the HOT wire to the other terminal screw on the
wall switch.
DESCRIPTION
AND FEATURES
The
Z
WN-RSM1-PLUS
utilizes Z-Wave technology to provide full control of the connected
device from your Internet Browser or Smart Phone App. It
is fully compatible with other Z-Wave
devices and can be added to most Z-Wave compliant controllers.
This smart relay can be used
to convert a continuous load into a
remotely switched load
or used in conjunction with the
existing manual switch to add remote operability.
For the advanced users of Z-Wave, the
functions can be customized with programming codes
.
•
Replaces existing relay with a technologically advanced relay that can be manually
controlled with conjoining switch or remotely through the Z-Wave network.
•
Preprogrammed and Customizable functions: Set scenes, schedule events (Program
ON/OFF times like a timer), and even turn ON/OFF when a motion or door sensor goes
off.
•
Compatible with CFL, fluorescent, incandescent, and halogen bulbs.
•
Works with existing light switches. NEUTRAL wire required at the relay.
•
Low Profile design allows for easy In-Box installation.
•
Signal repeater: repeats other connected Z-Wave devices and controllers, therefore
broadening the area of coverage.
INSTALLING
Z-WAVE
RELAYS
INSTALLATION
Installing a smart Z-Wave relay in conjunction with a standard switch
is a simple way to modernize your home by adding programmable lighting control to your smart device.
The ZW
N
-RSM1-PLUS
Smart
Relay
enables you to
add any compatible light to the Z-Wave network. Follow these directions to wire the relay.
If you have trouble identifying the wires, STOP and
consult with an Electrician.
WIRING DIRECTIONS
DO NOT REVERSE THE HOT AND
LOAD
WIRES.
DOING SO WILL VOID YOUR WARRANTY AND THE
RELAY
WILL SHORT CIRCUIT.
Step 1.
Identify all your wires. Label the wires or draw a diagram of existing wires.
Make sure there is
a NEUTRAL, HOT, and LOAD wire where the
ZWN-RSM1-PLUS
will be installed.
S
tep 2.
Connect the wires
according to the Diagram.
REQUIREMENTS
Z-Wave devices require a connection to a compatible hub. Once the device is properly added to
the hub, it can be managed and customized to your needs. Please visit
www.enerwaveautomation.com for a list of compatible hubs. NEUTRAL wire is required.
SPECIFICATIONS
Voltage...............................................................................
..........
...120
-277
VAC,
50/
60Hz
Maximum Load
.....................................................................................................
...
......
10A
Operating Temperature....................................................................................... 32-104° F
Z-Wave Frequency.......................................................................................... 908.42 MHz
Range.........................................................................................Up to 1
5
0 feet line of sight
........................between the Wireless Controller and the closest Z-Wave receiver module.
FCC COMPLIANCE
STATEMENT
FCC Grant of Equipment Authorizations of this device and transmitters installed in this device can be found at FCC website by entering the FCC ID number on the device.
Caution:
C
hanges or modifications not expressly approved by the part responsible for compliance could void the user’s
right
to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation of the device.
T
his equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
PLUS
NEW
Z-WAVE 500 SERIES
FEATURES
−
50% improvement in battery life
−
67% improvement in range
−
250% more bandwidth
−
Three RF channels for improved noise immunity and higher bandwidth
−
New Plug-n-Play Network-wide Inclusion feature
−
Improved self-healing and fault tolerance with Explorer Frame feature
−
Standardized method for Over the Air firmware updates (OTA)
−
Improved product information capture for product certification database
−
Fully backward compatible
