1 –
eLEDing
Solar Light Body 1 – Rechargeable Li-Poly Battery 1 – Tempered Glass Solar Panel
1 – Wall Mounting Plate w/hardware 2 – Hardware Package with Screws and Anchors
Model EE818plus User Manual
Initial Installation Set-up
(
Refer to Fig. 1)
Included in this package:
IMPORTANT
….
Read this User Manual Before Installing...!!!
®
Connecting the Battery before setting up
1.
The battery has been pre-charged before shipping and the light is ready for use
2. Make sure the main switch is in the
OFF
position
3. Open the battery cover on the back of the light and plug the battery into the connector and carefully make sure the plug position is
correct then replace the cover (Fig. 1-1)
4. Initially check the light and battery by moving the switch to
SMART
(
ON),
it should light up, then turn the switch back to
OFF
for installation
Mounting the Light Body
1. The light body
must only be mounted in a vertical position
and it should be mounted at least 6 to 10 feet above the ground
2. Choose a flat and safe mounting surface. Mark the screw positions through the mounting plate screw holes onto the mounting surface
Use 2 or 4 hole mount, (Fig. 1-2 & 1-3)
3. For wood, vinyl and metal surfaces mount the back plate directly with provided screws. Drill clearance holes using a 3/16" masonry bit
for surface of concrete, brick or stucco. Insert the anchors provided with screws then position the mounting plate and screw the
fasteners in securely
4.
Attach the light body unit
to the wall mounting plate:
Slide the whole light body onto the wall mount plate from top going down with the light body “hinged” to the mounting plate (Fig. 1-4)
Then secure the mounting with the small securing screw on bottom of the light body (Fig. 1-5)
5. With the light body firmly secured in it’s mounting position, the
Pan & Tilt
adjustment features can be used to adjust the direction of the
motion detector and the light head directions for optimal performance and coverage. The direction and angle of the motion detector can
be adjusted (Fig. 1-9). The LED light head can also be adjusted horizontally 180
o
, forward and backward 120
o
(Fig. 1-10)
Mounting and Connecting the Solar Panel
1. The solar panel must be mounted in a non-obstructed position where it will receive an average of at least 4 hours daily of direct sunlight
all year round. It should be mounted with a tilt of 35°- 80° degrees (Fig 1-6). A sturdy mounting location such as a wall, roof, on top of
patio, under the eaves, secure pole, or floor/ground base. This is required to make sure the solar panel is fastened down properly for all
weather conditions.
2. For Northern hemisphere installations the solar panel should be mounted with a Southerly facing position and visa-versa for Southern
hemisphere installation should face to the North (Australia, South Africa, South America e. g.)
3. Attach the hardware mounting bracket to the solar panel. Determine what length of the 10' connecting wire cord is needed to reach
the position of the light body and then tie the unused cord behind the solar panel with the plastic zip-tie that is provided (Fig. 1-7)
4. Then mark the screw holes through the mounting bracket and secure the solar panel in position with the provided hardware
5. Firmly plug the solar panel plug into the bottom of the light body (Fig. 1-8).
The RED-LED indicator (inside the motion ball) will
begin to double flash
(Fig. 1-8) indicating that charging status is active during a normal daytime sunny, partially sunny or cloudy day. If
this does not happen please check that the plug is fully plugged into the light body or if there is a problem with the wire.
SMART Solar Light … Built with
CREE
Ultra-Bright LED
Rev. EE818plus 01122016 Page 1
9
“eLEDing”
Solar Lights are SMART lights and they have an
embedded intelligent microprocessor control chip. The light has two
operating modes,
‘
SMART-ON MODE’
and
‘AUTO
MODE’.
Both are
SMART modes of operation and utilize stored energy capacity for the
most optimum lighting efficiency.
The “settings” for Sensitivity/Range of motion, length of illuminating
time, levels of brightness and dimming are set and controlled with
adjustable dials (Fig. 2)
The family of
eLEDing
SMART solar lights use an exclusive
Intelligent Power Management
(IPM)
embedded feature for
managing and optimizing the Lithium based battery for a full range of
operation.
This optimizes the battery’s life cycle to adapt to most
environmental conditions allowing both the battery and light to perform
for many years.
Fig. 2 – Main Switch & Control Settings
Battery will charge with the switch in either OFF or SMART ON position
Warm W
hite
Illumina
tion
Or
Pure W
hite
Illumina
tion
4.
5.
6.
3.
7.
8.
T
P
9.
Pan & Tilt
Pan & Tilt
p
10.
2 Screws
4 Screws
T
3.
1.
2.
Connect
the battery
before
using!
Just “One Easy Step” to Begin Using the Light
After the battery is connected and the light fixture and solar panel
are mounted you may immediately begin using the light by just
moving the main switch to the
SMART (ON)
position. Using the
factory pre-set profile is recommended (Fig.2).
Note: NO FURTHER ADJUSTMENTS ARE NECESSARY
