A.
L.
J.
K.
B.
C.
I. D.
F.
E.
H.
G.
NOTICE
All instructions, warranties and other collateral documents are subject to change
at the sole discretion of Horizon Hobby, Inc. For up-to-date product literature, visit
horizonhobby.com and click on the support tab for this product.
Meaning of Special Language
The following terms are used throughout the product literature to indicate various
levels of potential harm when operating this product:
NOTICE:
Procedures, which if not properly followed, create a possibility of physical
property damage AND a little or no possibility of injury.
CAUTION:
Procedures, which if not properly followed, create the probability of
physical property damage AND a possibility of serious injury.
WARNING:
Procedures, which if not properly followed, create the probability of
property damage, collateral damage, and serious injury OR create a high probability
of superficial injury.
WARNING:
Read the ENTIRE instruction manual to become familiar with the
features of the product before operating. Failure to operate the product
correctly can result in damage to the product, personal property and cause
serious injury.
This is a sophisticated hobby product. It must be operated with caution and common
sense and requires some basic mechanical ability. Failure to operate this Product
in a safe and responsible manner could result in injury or damage to the product or
other property. This product is not intended for use by children without direct adult
supervision. Do not attempt disassembly, use with incompatible components or
augment product in any way without the approval of Horizon Hobby, Inc. This manual
contains instructions for safety, operation and maintenance. It is essential to read and
follow all the instructions and warnings in the manual, prior to assembly, setup or use,
in order to operate correctly and avoid damage or serious injury.
Age Recommendation: Not for children under 14 years. This is not a toy.
SAfETy PRECAUTIONS ANd WARNINGS
WARNING:
Failure to exercise caution while using this product and comply
with the following warnings could result in product malfunction, electrical
issues, excessive heat, FIRE, and ultimately injury and property damage.
• Never leave the power supply, charger and battery unattended during use.
• Never attempt to charge dead, damaged or wet battery packs.
• Never attempt to charge a battery pack containing different types of batteries.
• Never allow children under 14 years of age to charge battery packs.
• Never charge batteries in extremely hot or cold places or place in direct sunlight.
• Never charge a battery if the cable has been pinched or shorted.
• Never connect the charger if the power cable has been pinched or shorted.
• Never connect the charger to an automobile 12V battery while the vehicle
is running.
• Never attempt to dismantle the charger or use a damaged charger.
• Never attach your charger to both an AC and a DC power source at the same time.
• Never connect the input jack (DC input) to AC power.
• Always use only rechargeable batteries designed for use with this type of charger.
• Always inspect the battery before charging.
• Always keep the battery away from any material that could be affected by heat.
• Always monitor the charging area and have a fire extinguisher available at all times.
• Always end the charging process if the battery becomes hot to the touch or starts
to change form (swell) during the charge process.
• Always connect the charge cable to the charger first, then connect the battery to
avoid short circuit between the charge leads. Reverse the sequence when
disconnecting.
• Always connect the positive red leads (+) and negative black leads (–) correctly.
• Always disconnect the battery after charging, and let the charger cool between
charges.
• Always charge in a well-ventilated area.
• Always terminate all processes and contact Horizon Hobby if the product
malfunctions.
WARNING:
Never leave charger unattended, exceed maximum charge rate,
charge with non-approved batteries or charge batteries in the wrong mode.
Failure to comply may result in excessive heat, fire and serious injury.
CAUTION:
Always ensure the battery you are charging meets the
specifications of this charger and that the charger settings are correct. Not
doing so can result in excessive heat and other related product malfunctions,
which can lead to user injury or property damage. Please contact Horizon
Hobby or an authorized retailer with compatibility questions.
InstructIon Manual | BedIenungsanleItung | Manuel d’utIlIsatIon | Manuale dI IstruzIonI
(dYn4300)
Included Items
JST_XH Balance adapter (2)
Banana plug to EC3
™
battery connector (2)
AC power cord (one region-US, EU, AU or UK)
OPTIONAL ACCESSORIES
DYN4012 - DC Power Cord
DYN5031 - Insulated Charge Adapter, Banana to EC3 Device
DYN5032 - Balancing Adapter Board
DYN5033 - Temperature Sensor: DYN4103, DYN4300
Minimum computer requirements for use of included software: Microsoft
®
Windows XP
®
, Windows 7
®
or Windows Vista
®
operating system, Compact disk (CD)
reader capable of reading a mini-CD and USB 2.0 port.
fEATURES
• Two charging ports to charge two batteries at once. Batteries can be different
capacities and cell counts
• 1A USB charge port compatible with iPhone
®
, iPod
®
or similar products
• 100–240V AC (50/60Hz) or 11–18V DC input voltage
• Li-Ion/Li-Po/Li-Fe battery cell count of 1 to 6 series cells
• Ni-Cd/Ni-MH battery cell count of 1 to 15 cells
• Pb battery voltage of 2 to 20V
• Built-in 50W discharger
• Built-in balance circuit
• Short-circuit, over-current, reverse polarity, low input voltage and
over-temperature protection
• Storage and Fast Charge modes
• User battery data, store and load up to 10 battery profiles
• (2) 2x16 backlit, blue LCD
• Insulated, color coded, banana jack, power output terminals (Red = Positive (+),
Black = Common or Negative (–))
• Internal cooling fans with grill covers
• Operating temperature range of 0°C to +50°C
• Meets IP33CW, IK07 environmental specs
• Rugged industrial plastic case
SPECIfICATIONS
AC Input Voltage 100–240V AC (50/60Hz)
DC Input Voltage 11–18V DC
Charge Current 0.10 to 10.0A per channel (in 0.1A increments/200W
maximum per channel/400W Total)
Discharge Current 0.10 to 5.0A per channel (in 0.1A increments/25W
maximum per channel/50W Total)
Operating temperature 0°C to +50°C
Balance Current Drain 300mA per cell
Trickle Charge Current 50 to 200mA
Charging Mode Peak (Ni-Cd/Ni-MH), CC/CV (Li-Po/Li-Ion/Li-Fe/Pb)
GETTING STARTEd
CAUTION:
Never connect the AC and DC input cords to an active power
source at the same time. This will void the warranty, cause product
damage and possibly injure the user.
When Using an External dC Power Source:
1. Connect the DC power cord to the charger DC power input port.
2. Connect the DC alligator clips to the DC power source.
3. Power ON the charger with the power switch.
4. When the charger is powered ON, a message will appear on the LCD screen.
NOTICE:
Always connect cable polarities correctly.
NOTICE:
Always consult 12V battery collateral materials or Horizon Hobby before
using with sources other than a standard AC wall outlet.
When Using an External AC Power Source:
1. Connect the AC power cord to the charger AC power input port.
2. Connect the AC power cord to the AC power source.
3. Power ON the charger with the power switch.
4. When the charger is powered ON, a message will appear on the LCD screen.
CAUTION:
Always power ON the charger before connecting a battery, or
damage to the charger and the battery can result.
1. Connect the charger to the power source.
2. Power ON the charger.
3. Make program selections in the charger for battery charging.
4. Connect the charger adapters to the charger.
5. Connect the battery to the charger adapters (connect main charging
connectors before connecting cell-balancing connectors, where used).
6. Start battery charging.
A.
Power Output Red (+)
B.
Power Output Black (–)
C.
Balance Circuit Adapter
Board Connector
d.
Temperature Probe Connection
E.
Mode/Stop Key
f.
USB Communications Port
G.
1A USB Charge Port
H.
Jog Dial
I.
LCD Screen
J.
AC Power Input Port
K.
Power Switch
L.
DC Power Input/
APP Connectors
PROGRAM SELECT
LiFe BATT
LiFe BALANCE
2.0A 19.8V(6S)
LiFe CHARGE
2.0A 19.8V(6S)
LiFe DISCHARGE
2.0A 19.8V(6S)
LiFe FAST CHG
2.0A 19.8V(6S)
LiFe STORAGE
2.0A 19.8V(6S)
PROGRAM SELECT
LiIo BATT
LiIo FAST CHG
2.0A 21.6V(6S)
LiIo BALANCE
2.0A 21.6V(6S)
LiIo CHARGE
2.0A 21.6V(6S)
LiIo STORAGE
2.0A 21.6V(6S)
LiIo DISCHARGE
2.0A 21.6V(6S)
PROGRAM SELECT
LiPo BATT
LiPo FAST CHG
2.0A 22.2V(6S)
LiPo BALANCE
2.0A 22.2V(6S)
LiPo CHARGE
2.0A 22.2V(6S)
LiPo STORAGE
2.0A 22.2V(6S)
LiPo DISCHARGE
2.0A 22.2V(6S)
PROGRAM SELECT
Pb BATT
Pb CHARGE
2.0A 2.0V (1P)
Pb DISCHARGE
2.0A 2.0V (1P)
PROGRAM SELECT
NiMH BATT
NiMH DISCHARGE
0.1A CUT:1.0V
NiMH CHARGE
CURRENT 2.0A
NiMH Auto CHARGE
CURRENT 2.0A
NiMH RE-PEAK
2
NiMH CYCLE
DCHG>CHG 1
PROGRAM SELECT
NiCd BATT
NiCd CHARGE
CURRENT 2.0A
NiCd DISCHARGE
0.1A CUT: 1.0V
NiCd RE-PEAK
2
NiCd CYCLE
DCHG>CHG 1
NiCd Auto CHARGE
CURRENT 2.0A
PROGRAM SELECT
LI BATT METER
0.00 0.00 0.00 V
0.00 0.00 0.00 V
MAIN 00.00V
H0.000V L0.000V
PROGRAM SELECT
BATT MEMORY
[BATT MEMORY 1]
ENTER SET ->
BATT TYPE
LiPo
TVC=YOUR RISK!
4.20V
DSCH VOLTAGE
3.0V/CELL
DSCH CURRENT
1.0A
CHARGE CURRENT
2.2A
BATT VOLTS
7.4V(2S)
SAVE PROGRAM
ENTER
TEMPERATURE
CUT-OFF 50C
PROGRAM SELECT
SYSTEM SET->
LOAD FACTORY SET
ENTER
Rest Time
CHG>DCHG 10min
VERSION
1.00
Key Beep ON
Buzzer ON
Ext. Temp 0C
Int. Temp 32C
Input Power Low
Cut-Off 11.0V
Capacity Cut-Off
ON 5000mAh
SAFETY TIMER
ON 120min
PROGRAM SELECT
LiFe BATT
LiFe BALANCE
2.0A 19.8V(6S)
LiFe CHARGE
2.0A 19.8V(6S)
LiFe DISCHARGE
2.0A 19.8V(6S)
LiFe FAST CHG
2.0A 19.8V(6S)
LiFe STORAGE
2.0A 19.8V(6S)
PROGRAM SELECT
LiIo BATT
LiIo FAST CHG
2.0A 21.6V(6S)
LiIo BALANCE
2.0A 21.6V(6S)
LiIo CHARGE
2.0A 21.6V(6S)
LiIo STORAGE
2.0A 21.6V(6S)
LiIo DISCHARGE
2.0A 21.6V(6S)
PROGRAM SELECT
LiPo BATT
LiPo FAST CHG
2.0A 22.2V(6S)
LiPo BALANCE
2.0A 22.2V(6S)
LiPo CHARGE
2.0A 22.2V(6S)
LiPo STORAGE
2.0A 22.2V(6S)
LiPo DISCHARGE
2.0A 22.2V(6S)
PROGRAM SELECT
Pb BATT
Pb CHARGE
2.0A 2.0V (1P)
Pb DISCHARGE
2.0A 2.0V (1P)
PROGRAM SELECT
NiMH BATT
NiMH DISCHARGE
0.1A CUT:1.0V
NiMH CHARGE
CURRENT 2.0A
NiMH Auto CHARGE
CURRENT 2.0A
NiMH RE-PEAK
2
NiMH CYCLE
DCHG>CHG 1
PROGRAM SELECT
NiCd BATT
NiCd CHARGE
CURRENT 2.0A
NiCd DISCHARGE
0.1A CUT: 1.0V
NiCd RE-PEAK
2
NiCd CYCLE
DCHG>CHG 1
NiCd Auto CHARGE
CURRENT 2.0A
PROGRAM SELECT
LI BATT METER
0.00 0.00 0.00 V
0.00 0.00 0.00 V
MAIN 00.00V
H0.000V L0.000V
PROGRAM SELECT
BATT MEMORY
[BATT MEMORY 1]
ENTER SET ->
BATT TYPE
LiPo
TVC=YOUR RISK!
4.20V
DSCH VOLTAGE
3.0V/CELL
DSCH CURRENT
1.0A
CHARGE CURRENT
2.2A
BATT VOLTS
7.4V(2S)
SAVE PROGRAM
ENTER
TEMPERATURE
CUT-OFF 50C
PROGRAM SELECT
SYSTEM SET->
LOAD FACTORY SET
ENTER
Rest Time
CHG>DCHG 10min
VERSION
1.00
Key Beep ON
Buzzer ON
Ext. Temp 0C
Int. Temp 32C
Input Power Low
Cut-Off 11.0V
Capacity Cut-Off
ON 5000mAh
SAFETY TIMER
ON 120min
PROGRAM SELECT
LiFe BATT
LiFe BALANCE
2.0A 19.8V(6S)
LiFe CHARGE
2.0A 19.8V(6S)
LiFe DISCHARGE
2.0A 19.8V(6S)
LiFe FAST CHG
2.0A 19.8V(6S)
LiFe STORAGE
2.0A 19.8V(6S)
PROGRAM SELECT
LiIo BATT
LiIo FAST CHG
2.0A 21.6V(6S)
LiIo BALANCE
2.0A 21.6V(6S)
LiIo CHARGE
2.0A 21.6V(6S)
LiIo STORAGE
2.0A 21.6V(6S)
LiIo DISCHARGE
2.0A 21.6V(6S)
PROGRAM SELECT
LiPo BATT
LiPo FAST CHG
2.0A 22.2V(6S)
LiPo BALANCE
2.0A 22.2V(6S)
LiPo CHARGE
2.0A 22.2V(6S)
LiPo STORAGE
2.0A 22.2V(6S)
LiPo DISCHARGE
2.0A 22.2V(6S)
PROGRAM SELECT
Pb BATT
Pb CHARGE
2.0A 2.0V (1P)
Pb DISCHARGE
2.0A 2.0V (1P)
PROGRAM SELECT
NiMH BATT
NiMH DISCHARGE
0.1A CUT:1.0V
NiMH CHARGE
CURRENT 2.0A
NiMH Auto CHARGE
CURRENT 2.0A
NiMH RE-PEAK
2
NiMH CYCLE
DCHG>CHG 1
PROGRAM SELECT
NiCd BATT
NiCd CHARGE
CURRENT 2.0A
NiCd DISCHARGE
0.1A CUT: 1.0V
NiCd RE-PEAK
2
NiCd CYCLE
DCHG>CHG 1
NiCd Auto CHARGE
CURRENT 2.0A
PROGRAM SELECT
LI BATT METER
0.00 0.00 0.00 V
0.00 0.00 0.00 V
MAIN 00.00V
H0.000V L0.000V
PROGRAM SELECT
BATT MEMORY
[BATT MEMORY 1]
ENTER SET ->
BATT TYPE
LiPo
TVC=YOUR RISK!
4.20V
DSCH VOLTAGE
3.0V/CELL
DSCH CURRENT
1.0A
CHARGE CURRENT
2.2A
BATT VOLTS
7.4V(2S)
SAVE PROGRAM
ENTER
TEMPERATURE
CUT-OFF 50C
PROGRAM SELECT
SYSTEM SET->
LOAD FACTORY SET
ENTER
Rest Time
CHG>DCHG 10min
VERSION
1.00
Key Beep ON
Buzzer ON
Ext. Temp 0C
Int. Temp 32C
Input Power Low
Cut-Off 11.0V
Capacity Cut-Off
ON 5000mAh
SAFETY TIMER
ON 120min
PROGRAM SELECT
LiFe BATT
LiFe BALANCE
2.0A 19.8V(6S)
LiFe CHARGE
2.0A 19.8V(6S)
LiFe DISCHARGE
2.0A 19.8V(6S)
LiFe FAST CHG
2.0A 19.8V(6S)
LiFe STORAGE
2.0A 19.8V(6S)
PROGRAM SELECT
LiIo BATT
LiIo FAST CHG
2.0A 21.6V(6S)
LiIo BALANCE
2.0A 21.6V(6S)
LiIo CHARGE
2.0A 21.6V(6S)
LiIo STORAGE
2.0A 21.6V(6S)
LiIo DISCHARGE
2.0A 21.6V(6S)
PROGRAM SELECT
LiPo BATT
LiPo FAST CHG
2.0A 22.2V(6S)
LiPo BALANCE
2.0A 22.2V(6S)
LiPo CHARGE
2.0A 22.2V(6S)
LiPo STORAGE
2.0A 22.2V(6S)
LiPo DISCHARGE
2.0A 22.2V(6S)
PROGRAM SELECT
Pb BATT
Pb CHARGE
2.0A 2.0V (1P)
Pb DISCHARGE
2.0A 2.0V (1P)
PROGRAM SELECT
NiMH BATT
NiMH DISCHARGE
0.1A CUT:1.0V
NiMH CHARGE
CURRENT 2.0A
NiMH Auto CHARGE
CURRENT 2.0A
NiMH RE-PEAK
2
NiMH CYCLE
DCHG>CHG 1
PROGRAM SELECT
NiCd BATT
NiCd CHARGE
CURRENT 2.0A
NiCd DISCHARGE
0.1A CUT: 1.0V
NiCd RE-PEAK
2
NiCd CYCLE
DCHG>CHG 1
NiCd Auto CHARGE
CURRENT 2.0A
PROGRAM SELECT
LI BATT METER
0.00 0.00 0.00 V
0.00 0.00 0.00 V
MAIN 00.00V
H0.000V L0.000V
PROGRAM SELECT
BATT MEMORY
[BATT MEMORY 1]
ENTER SET ->
BATT TYPE
LiPo
TVC=YOUR RISK!
4.20V
DSCH VOLTAGE
3.0V/CELL
DSCH CURRENT
1.0A
CHARGE CURRENT
2.2A
BATT VOLTS
7.4V(2S)
SAVE PROGRAM
ENTER
TEMPERATURE
CUT-OFF 50C
PROGRAM SELECT
SYSTEM SET->
LOAD FACTORY SET
ENTER
Rest Time
CHG>DCHG 10min
VERSION
1.00
Key Beep ON
Buzzer ON
Ext. Temp 0C
Int. Temp 32C
Input Power Low
Cut-Off 11.0V
Capacity Cut-Off
ON 5000mAh
SAFETY TIMER
ON 120min
PROGRAM SELECT
LiFe BATT
LiFe BALANCE
2.0A 19.8V(6S)
LiFe CHARGE
2.0A 19.8V(6S)
LiFe DISCHARGE
2.0A 19.8V(6S)
LiFe FAST CHG
2.0A 19.8V(6S)
LiFe STORAGE
2.0A 19.8V(6S)
PROGRAM SELECT
LiIo BATT
LiIo FAST CHG
2.0A 21.6V(6S)
LiIo BALANCE
2.0A 21.6V(6S)
LiIo CHARGE
2.0A 21.6V(6S)
LiIo STORAGE
2.0A 21.6V(6S)
LiIo DISCHARGE
2.0A 21.6V(6S)
PROGRAM SELECT
LiPo BATT
LiPo FAST CHG
2.0A 22.2V(6S)
LiPo BALANCE
2.0A 22.2V(6S)
LiPo CHARGE
2.0A 22.2V(6S)
LiPo STORAGE
2.0A 22.2V(6S)
LiPo DISCHARGE
2.0A 22.2V(6S)
PROGRAM SELECT
Pb BATT
Pb CHARGE
2.0A 2.0V (1P)
Pb DISCHARGE
2.0A 2.0V (1P)
PROGRAM SELECT
NiMH BATT
NiMH DISCHARGE
0.1A CUT:1.0V
NiMH CHARGE
CURRENT 2.0A
NiMH Auto CHARGE
CURRENT 2.0A
NiMH RE-PEAK
2
NiMH CYCLE
DCHG>CHG 1
PROGRAM SELECT
NiCd BATT
NiCd CHARGE
CURRENT 2.0A
NiCd DISCHARGE
0.1A CUT: 1.0V
NiCd RE-PEAK
2
NiCd CYCLE
DCHG>CHG 1
NiCd Auto CHARGE
CURRENT 2.0A
PROGRAM SELECT
LI BATT METER
0.00 0.00 0.00 V
0.00 0.00 0.00 V
MAIN 00.00V
H0.000V L0.000V
PROGRAM SELECT
BATT MEMORY
[BATT MEMORY 1]
ENTER SET ->
BATT TYPE
LiPo
TVC=YOUR RISK!
4.20V
DSCH VOLTAGE
3.0V/CELL
DSCH CURRENT
1.0A
CHARGE CURRENT
2.2A
BATT VOLTS
7.4V(2S)
SAVE PROGRAM
ENTER
TEMPERATURE
CUT-OFF 50C
PROGRAM SELECT
SYSTEM SET->
LOAD FACTORY SET
ENTER
Rest Time
CHG>DCHG 10min
VERSION
1.00
Key Beep ON
Buzzer ON
Ext. Temp 0C
Int. Temp 32C
Input Power Low
Cut-Off 11.0V
Capacity Cut-Off
ON 5000mAh
SAFETY TIMER
ON 120min
PROGRAM SELECT
LiFe BATT
LiFe BALANCE
2.0A 19.8V(6S)
LiFe CHARGE
2.0A 19.8V(6S)
LiFe DISCHARGE
2.0A 19.8V(6S)
LiFe FAST CHG
2.0A 19.8V(6S)
LiFe STORAGE
2.0A 19.8V(6S)
PROGRAM SELECT
LiIo BATT
LiIo FAST CHG
2.0A 21.6V(6S)
LiIo BALANCE
2.0A 21.6V(6S)
LiIo CHARGE
2.0A 21.6V(6S)
LiIo STORAGE
2.0A 21.6V(6S)
LiIo DISCHARGE
2.0A 21.6V(6S)
PROGRAM SELECT
LiPo BATT
LiPo FAST CHG
2.0A 22.2V(6S)
LiPo BALANCE
2.0A 22.2V(6S)
LiPo CHARGE
2.0A 22.2V(6S)
LiPo STORAGE
2.0A 22.2V(6S)
LiPo DISCHARGE
2.0A 22.2V(6S)
PROGRAM SELECT
Pb BATT
Pb CHARGE
2.0A 2.0V (1P)
Pb DISCHARGE
2.0A 2.0V (1P)
PROGRAM SELECT
NiMH BATT
NiMH DISCHARGE
0.1A CUT:1.0V
NiMH CHARGE
CURRENT 2.0A
NiMH Auto CHARGE
CURRENT 2.0A
NiMH RE-PEAK
2
NiMH CYCLE
DCHG>CHG 1
PROGRAM SELECT
NiCd BATT
NiCd CHARGE
CURRENT 2.0A
NiCd DISCHARGE
0.1A CUT: 1.0V
NiCd RE-PEAK
2
NiCd CYCLE
DCHG>CHG 1
NiCd Auto CHARGE
CURRENT 2.0A
PROGRAM SELECT
LI BATT METER
0.00 0.00 0.00 V
0.00 0.00 0.00 V
MAIN 00.00V
H0.000V L0.000V
PROGRAM SELECT
BATT MEMORY
[BATT MEMORY 1]
ENTER SET ->
BATT TYPE
LiPo
TVC=YOUR RISK!
4.20V
DSCH VOLTAGE
3.0V/CELL
DSCH CURRENT
1.0A
CHARGE CURRENT
2.2A
BATT VOLTS
7.4V(2S)
SAVE PROGRAM
ENTER
TEMPERATURE
CUT-OFF 50C
PROGRAM SELECT
SYSTEM SET->
LOAD FACTORY SET
ENTER
Rest Time
CHG>DCHG 10min
VERSION
1.00
Key Beep ON
Buzzer ON
Ext. Temp 0C
Int. Temp 32C
Input Power Low
Cut-Off 11.0V
Capacity Cut-Off
ON 5000mAh
SAFETY TIMER
ON 120min
PROGRAM SELECT
LiFe BATT
LiFe BALANCE
2.0A 19.8V(6S)
LiFe CHARGE
2.0A 19.8V(6S)
LiFe DISCHARGE
2.0A 19.8V(6S)
LiFe FAST CHG
2.0A 19.8V(6S)
LiFe STORAGE
2.0A 19.8V(6S)
PROGRAM SELECT
LiIo BATT
LiIo FAST CHG
2.0A 21.6V(6S)
LiIo BALANCE
2.0A 21.6V(6S)
LiIo CHARGE
2.0A 21.6V(6S)
LiIo STORAGE
2.0A 21.6V(6S)
LiIo DISCHARGE
2.0A 21.6V(6S)
PROGRAM SELECT
LiPo BATT
LiPo FAST CHG
2.0A 22.2V(6S)
LiPo BALANCE
2.0A 22.2V(6S)
LiPo CHARGE
2.0A 22.2V(6S)
LiPo STORAGE
2.0A 22.2V(6S)
LiPo DISCHARGE
2.0A 22.2V(6S)
PROGRAM SELECT
Pb BATT
Pb CHARGE
2.0A 2.0V (1P)
Pb DISCHARGE
2.0A 2.0V (1P)
PROGRAM SELECT
NiMH BATT
NiMH DISCHARGE
0.1A CUT:1.0V
NiMH CHARGE
CURRENT 2.0A
NiMH Auto CHARGE
CURRENT 2.0A
NiMH RE-PEAK
2
NiMH CYCLE
DCHG>CHG 1
PROGRAM SELECT
NiCd BATT
NiCd CHARGE
CURRENT 2.0A
NiCd DISCHARGE
0.1A CUT: 1.0V
NiCd RE-PEAK
2
NiCd CYCLE
DCHG>CHG 1
NiCd Auto CHARGE
CURRENT 2.0A
PROGRAM SELECT
LI BATT METER
0.00 0.00 0.00 V
0.00 0.00 0.00 V
MAIN 00.00V
H0.000V L0.000V
PROGRAM SELECT
BATT MEMORY
[BATT MEMORY 1]
ENTER SET ->
BATT TYPE
LiPo
TVC=YOUR RISK!
4.20V
DSCH VOLTAGE
3.0V/CELL
DSCH CURRENT
1.0A
CHARGE CURRENT
2.2A
BATT VOLTS
7.4V(2S)
SAVE PROGRAM
ENTER
TEMPERATURE
CUT-OFF 50C
PROGRAM SELECT
SYSTEM SET->
LOAD FACTORY SET
ENTER
Rest Time
CHG>DCHG 10min
VERSION
1.00
Key Beep ON
Buzzer ON
Ext. Temp 0C
Int. Temp 32C
Input Power Low
Cut-Off 11.0V
Capacity Cut-Off
ON 5000mAh
SAFETY TIMER
ON 120min
PROGRAM SELECT
LiFe BATT
LiFe BALANCE
2.0A 19.8V(6S)
LiFe CHARGE
2.0A 19.8V(6S)
LiFe DISCHARGE
2.0A 19.8V(6S)
LiFe FAST CHG
2.0A 19.8V(6S)
LiFe STORAGE
2.0A 19.8V(6S)
PROGRAM SELECT
LiIo BATT
LiIo FAST CHG
2.0A 21.6V(6S)
LiIo BALANCE
2.0A 21.6V(6S)
LiIo CHARGE
2.0A 21.6V(6S)
LiIo STORAGE
2.0A 21.6V(6S)
LiIo DISCHARGE
2.0A 21.6V(6S)
PROGRAM SELECT
LiPo BATT
LiPo FAST CHG
2.0A 22.2V(6S)
LiPo BALANCE
2.0A 22.2V(6S)
LiPo CHARGE
2.0A 22.2V(6S)
LiPo STORAGE
2.0A 22.2V(6S)
LiPo DISCHARGE
2.0A 22.2V(6S)
PROGRAM SELECT
Pb BATT
Pb CHARGE
2.0A 2.0V (1P)
Pb DISCHARGE
2.0A 2.0V (1P)
PROGRAM SELECT
NiMH BATT
NiMH DISCHARGE
0.1A CUT:1.0V
NiMH CHARGE
CURRENT 2.0A
NiMH Auto CHARGE
CURRENT 2.0A
NiMH RE-PEAK
2
NiMH CYCLE
DCHG>CHG 1
PROGRAM SELECT
NiCd BATT
NiCd CHARGE
CURRENT 2.0A
NiCd DISCHARGE
0.1A CUT: 1.0V
NiCd RE-PEAK
2
NiCd CYCLE
DCHG>CHG 1
NiCd Auto CHARGE
CURRENT 2.0A
PROGRAM SELECT
LI BATT METER
0.00 0.00 0.00 V
0.00 0.00 0.00 V
MAIN 00.00V
H0.000V L0.000V
PROGRAM SELECT
BATT MEMORY
[BATT MEMORY 1]
ENTER SET ->
BATT TYPE
LiPo
TVC=YOUR RISK!
4.20V
DSCH VOLTAGE
3.0V/CELL
DSCH CURRENT
1.0A
CHARGE CURRENT
2.2A
BATT VOLTS
7.4V(2S)
SAVE PROGRAM
ENTER
TEMPERATURE
CUT-OFF 50C
PROGRAM SELECT
SYSTEM SET->
LOAD FACTORY SET
ENTER
Rest Time
CHG>DCHG 10min
VERSION
1.00
Key Beep ON
Buzzer ON
Ext. Temp 0C
Int. Temp 32C
Input Power Low
Cut-Off 11.0V
Capacity Cut-Off
ON 5000mAh
SAFETY TIMER
ON 120min
PROGRAM SELECT
LiFe BATT
LiFe BALANCE
2.0A 19.8V(6S)
LiFe CHARGE
2.0A 19.8V(6S)
LiFe DISCHARGE
2.0A 19.8V(6S)
LiFe FAST CHG
2.0A 19.8V(6S)
LiFe STORAGE
2.0A 19.8V(6S)
PROGRAM SELECT
LiIo BATT
LiIo FAST CHG
2.0A 21.6V(6S)
LiIo BALANCE
2.0A 21.6V(6S)
LiIo CHARGE
2.0A 21.6V(6S)
LiIo STORAGE
2.0A 21.6V(6S)
LiIo DISCHARGE
2.0A 21.6V(6S)
PROGRAM SELECT
LiPo BATT
LiPo FAST CHG
2.0A 22.2V(6S)
LiPo BALANCE
2.0A 22.2V(6S)
LiPo CHARGE
2.0A 22.2V(6S)
LiPo STORAGE
2.0A 22.2V(6S)
LiPo DISCHARGE
2.0A 22.2V(6S)
PROGRAM SELECT
Pb BATT
Pb CHARGE
2.0A 2.0V (1P)
Pb DISCHARGE
2.0A 2.0V (1P)
PROGRAM SELECT
NiMH BATT
NiMH DISCHARGE
0.1A CUT:1.0V
NiMH CHARGE
CURRENT 2.0A
NiMH Auto CHARGE
CURRENT 2.0A
NiMH RE-PEAK
2
NiMH CYCLE
DCHG>CHG 1
PROGRAM SELECT
NiCd BATT
NiCd CHARGE
CURRENT 2.0A
NiCd DISCHARGE
0.1A CUT: 1.0V
NiCd RE-PEAK
2
NiCd CYCLE
DCHG>CHG 1
NiCd Auto CHARGE
CURRENT 2.0A
PROGRAM SELECT
LI BATT METER
0.00 0.00 0.00 V
0.00 0.00 0.00 V
MAIN 00.00V
H0.000V L0.000V
PROGRAM SELECT
BATT MEMORY
[BATT MEMORY 1]
ENTER SET ->
BATT TYPE
LiPo
TVC=YOUR RISK!
4.20V
DSCH VOLTAGE
3.0V/CELL
DSCH CURRENT
1.0A
CHARGE CURRENT
2.2A
BATT VOLTS
7.4V(2S)
SAVE PROGRAM
ENTER
TEMPERATURE
CUT-OFF 50C
PROGRAM SELECT
SYSTEM SET->
LOAD FACTORY SET
ENTER
Rest Time
CHG>DCHG 10min
VERSION
1.00
Key Beep ON
Buzzer ON
Ext. Temp 0C
Int. Temp 32C
Input Power Low
Cut-Off 11.0V
Capacity Cut-Off
ON 5000mAh
SAFETY TIMER
ON 120min
PROGRAMMING qUICK GUIdE
Press the
Mode key (G)
to get to the 9 main menus from any submenu screen.
Press the
Jog dial (H)
to get to the submenus for adjusting operating parameters, to save value changes or to start chosen battery charging actions.
Rotate the
Jog dial (H)
to change between submenu screens or to change screen values.
JST_XH ADAPTER
2S
3S
4S
6S
5S
JST_XH ADAPTER
2S
3S
4S
6S
5S
Not to scale.
Not all wiring shown.
Not all connectors shown.
OPERATING yOUR CHARGER
1
SELf TEST ANd PROGRAM SELECT SCREENS
Press the
Mode key
until you reach the 9 main menus, then rotate the
Jog dial
to
locate the PROGRAM SELECT LiFe BATT screen. Press the
Jog dial
to select LiFe.
Rotate the
Jog dial
to go to one of the control screens (BALANCE, CHARGE, FAST
CHG, STORAGE or DISCHARGE) to do what your battery needs.
Correctly connect your lithium battery to the charger (charging connector first and
balancing connector second). Press the
Jog dial
and adjust charging parameters
as needed. Press and hold the
Jog dial
(approximately 3 seconds) until the screen
changes to start the battery check/charge sequence.
R: 3SER
S:3SER
CONFIRM (ENTER)
A
When the charge cycle starts, the
charger compares the battery to the
charger settings. The screen will show
the battery and your settings
information. If the information after R: (charger) and S: (settings)
(A)
does not match,
press the
Mode key
and change the lithium battery charging parameters as
needed. If the R: information matches S:, press the
Jog dial
to confirm. After
confirmation, charging starts and information will show on the LCD screen
(information may vary).
LI 3S 2.0A 12.59V
BAL 022:43 01082
f
E
B C
d
A
A.
A Li-Fe battery pack is
balance charging
B.
Battery pack has 3 cells in
series
C.
Charging rate is 2.0A (2000mAh)
d.
Voltage being applied to the battery is currently 12.59V
E.
Present charge level of the battery is 1082mAh
f.
Time elapsed since the charge process started is 22:43 (22 minutes and 43
seconds)
During charging, the
Jog dial
can be rotated counterclockwise to show several
parameter messages on the LCD screen, including: End Voltage, Input Power Volt-
age, External & Internal Temperature, Temperature Cutoff, Safety Timer Status and
Capacity Cutoff.
Rotate the
Jog dial
clockwise to show the charge voltages for each cell. Press the
Jog dial
at any time to return to the Charge Monitor screen. The charger signals
when the charging (or discharging) process is complete (if Buzzer is set to ON).
CAUTION:
The Li-Fe program menus are to be used ONLY for the
charging and discharging of Li-Fe battery packs. The charging of other
battery types using these programs will result in damage to the battery or
charger.
CAUTION:
Using a charge rate that is not compatible with the battery
capacities may result in damage or malfunction of the charger or
batteries.
3
LI-fE BALANCE CHARGING
When the charger is powered ON, there is a series of self tests and the screen will
show the charger brand name and model number.
DYNAMITE
DYN4300
After the self tests, the charger will show another screen. The information on this
screen will vary but will look similar to this:
LiPo BALANCE
2.0A 7.4V(2S)
From any screen, press the
Mode key
to go back to the main menu.
2
LI-fE BATTERIES
Press the
Mode key
until you reach the 9 main menus, then rotate the
Jog dial
to
locate the PROGRAM SELECT LiFe BATT screen. Press the
Jog dial
to go into this
menu.
Rotate the
Jog dial
to go to the LiFe BALANCE screen and set charging param-
eters. The charging amperage
(A)
can be set between 0.1 and 10.0A. Voltage
(B)
is
dependent on the number of cells in series. For example, with Li-Fe batteries these
values can be from 3.3V (for 1S batteries) to 19.8V (for 6S batteries).
LiFe BALANCE
5.5A 19.8V(6S)
A
B
C
To select values other than the existing parameters:
• Press the
Jog dial
so the charge current value
(A)
flashes
• Rotate the
Jog dial
to INCREASE OR DECREASE the charge current value
• Press the
Jog dial
to save the value and the voltage value
(B)
flashes
• Rotate the
Jog dial
to INCREASE OR DECREASE the voltage (and # of cells in
series
(C)
)
• Press the
Jog dial
to save the voltage value
If no parameters are flashing, you can rotate the
Jog dial
to select another program
such as CHARGE, FAST CHG, STORAGE or DISCHARGE.
To start charging, press and hold the
Jog dial
for 3 seconds.
4
LI-fE CHARGING
Press the
Mode key
until you reach the 9 main menus, then rotate the
Jog dial
to
locate the PROGRAM SELECT LiFe BATT screen. Press the
Jog dial
to go into this
menu.
Rotate the
Jog dial
to go to the LiFe CHARGE screen and set charging parameters.
The charging amperage
(A)
can be set between 0.1 and 10.0A. Voltage
(B)
is
dependent on the number of cells in series. For example, with Li-Fe batteries these
values can be from 3.3V (for 1S batteries) to 19.8V (for 6S batteries).
LiFe CHARGE
4.6A 19.8V(6S)
A
B
C
To select values other than the existing parameters:
• Press the
Jog dial
so the charge current value
(A)
flashes
• Rotate the
Jog dial
to INCREASE OR DECREASE the charge current value
• Press the
Jog dial
to save the value and the voltage value
(B)
flashes
• Rotate the
Jog dial
to INCREASE OR DECREASE the voltage (and # of cells in
series
(C)
)
• Press the
Jog dial
to save the voltage value
If no parameters are flashing, you can rotate the
Jog dial
to select another program
such as BALANCE, FAST CHG, STORAGE or DISCHARGE.
To start charging, press and hold the
Jog dial
for 3 seconds.
CAUTION:
If at any time during the charge process the battery pack becomes
hot or begins to puff, disconnect the battery immediately and discontinue the
charge process as batteries can cause fire, collateral damage and injuries.
5
LI-fE fAST CHARGING
Press the
Mode key
until you reach the 9 main menus, then rotate the
Jog dial
to
locate the PROGRAM SELECT LiFe BATT screen. Press the
Jog dial
to go into this
menu.
Rotate the
Jog dial
to go to the LiFe FAST CHG screen and set charging param-
eters. The charging amperage
(A)
can be set between 0.1 and 10.0A. Voltage
(B)
is
dependent on the number of cells in series. For example, with Li-Fe batteries these
values can be from 3.3V (for 1S batteries) to 19.8V (for 6S batteries).
Near the end of a standard charging cycle, the charger switches from Constant Cur-
rent (CC) mode to Constant Voltage (CV) mode to slowly “top off” the current in the
battery as close as possible to the maximum capacity.
In Fast Charge, the CV mode is eliminated in order to greatly shorten the charging
time; however, the final capacity of the battery will be less than what you would get
using the standard charge method.
LiFe FAST CHG
0.1A 19.8V(6S)
A
B
C
To select values other than the existing parameters:
• Press the
Jog dial
so the charge current value
(A)
flashes
• Rotate the
Jog dial
to INCREASE OR DECREASE the charge current value
• Press the
Jog dial
to save the value and the voltage value
(B)
flashes
• Rotate the
Jog dial
to INCREASE OR DECREASE the voltage (and # of cells in
series
(C)
)
• Press the
Jog dial
to save the voltage value
If no parameters are flashing, you can rotate the
Jog dial
to select another program
such as CHARGE, BALANCE, STORAGE or DISCHARGE.
To start charging, press and hold the
Jog dial
for 3 seconds.
6
LI-fE STORAGE CHARGING
Press the
Mode key
until you reach the 9 main menus, then rotate the
Jog dial
to
locate the PROGRAM SELECT LiFe BATT screen. Press the
Jog dial
to go into this
menu.
Rotate the
Jog dial
to go to the LiFe STORAGE screen and set charging param-
eters. The charging amperage
(A)
can be set between 0.1 and 10.0A. Voltage
(B)
is
dependent on the number of cells in series. For example, with Li-Fe batteries these
values can be from 3.3V (for 1S batteries) to 19.8V (for 6S batteries).
If you don’t plan on using your battery for a long time, it is best to charge (or
discharge) the battery to its optimal storage voltage and capacity.
LiFe STORAGE
2.5A 19.8V(6S)
A
B
C
To select values other than the existing parameters:
• Press the
Jog dial
so the charge current value
(A)
flashes
• Rotate the
Jog dial
to INCREASE OR DECREASE the charge current value
• Press the
Jog dial
to save the value and the voltage value
(B)
flashes
• Rotate the
Jog dial
to INCREASE OR DECREASE the voltage (and # of cells in
series
(C)
)
• Press the
Jog dial
to save the voltage value
If no parameters are flashing, you can rotate the
Jog dial
to select another program
such as CHARGE, BALANCE, FAST CHG or DISCHARGE.
To start charging, press and hold the
Jog dial
for 3 seconds.
7
LI-fE dISCHARGING
Press the
Mode key
until you reach the 9 main menus, then rotate the
Jog dial
to
locate the PROGRAM SELECT LiFe BATT screen. Press the
Jog dial
to go into this
menu.
Rotate the
Jog dial
to go to the LiFe DISCHARGE screen and set discharging pa-
rameters. The discharging amperage
(A)
can be set between 0.1 and 5.0A. Voltage
(B)
is dependent on the number of cells in series. For example, with Li-Fe batteries
these values can be from 3.3V (for 1S batteries) to 19.8V (for 6S batteries).
A battery’s capacity can be verified by discharging it to its minimum voltage level
and measuring the current as the battery is discharged.
LiFe DISCHARGE
2.0A 19.8V(6S)
A
B
C
To select values other than the existing parameters:
• Press the
Jog dial
so the discharge current value
(A)
flashes
• Rotate the
Jog dial
to INCREASE OR DECREASE the discharge current value
• Press the
Jog dial
to save the value and the voltage value
(B)
flashes
• Rotate the
Jog dial
to INCREASE OR DECREASE the voltage (and # of cells in
series
(C)
)
• Press the
Jog dial
to save the voltage value
If no parameters are flashing, you can rotate the
Jog dial
to select another program
such as CHARGE, BALANCE, FAST CHG or STORAGE.
To start discharging, press and hold the
Jog dial
for 3 seconds.
8
LI-IO BATTERIES
Press the
Mode key
until you reach the 9 main menus, then rotate the
Jog dial
to
locate the PROGRAM SELECT LiIo BATT screen. Press the
Jog dial
to select LiIo.
Rotate the
Jog dial
to go to one of the control screens (BALANCE, CHARGE, FAST
CHG, STORAGE or DISCHARGE) to do what your battery needs.
Correctly connect your lithium battery to the charger (charging connector first and
balancing connector second). Press the
Jog dial
and adjust the charging param-
eters as needed. Press and hold the
Jog dial
(approximately 3 seconds) until the
screen changes to start the battery check/charge sequence.
R: 3SER
S:3SER
CONFIRM (ENTER)
A
When the charge cycle starts, the
charger compares the battery to
charger settings. The screen will show
the battery and your settings
information. If the information after R: (charger) and S: (settings)
(A)
does not match,
press the
Mode key
and change the lithium battery charging parameters as
needed. If the R: information matches S:, press the
Jog dial
to confirm.
After confirmation, charging starts and information will show on the LCD screen
(information may vary).
LI 3S 2.0A 12.59V
BAL 022:43 01082
f
E
B C
d
A
A.
A Li-Io battery pack is balance
charging
B.
Battery pack has 3 cells in
series
C.
Charging rate is 2.0A (2000mAh)
d.
Voltage being applied to the battery is currently 12.59V
E.
Present charge level of the battery is 1082mAh
f.
Time elapsed since the charge process started is 22:43
During charging, the
Jog dial
can be rotated counterclockwise to show several
parameter messages on the LCD screen, including: End Voltage, Input Power Volt-
age, External & Internal Temperature, Temperature Cutoff, Safety Timer Status and
Capacity Cutoff.
Rotate the
Jog dial
clockwise to show the charge voltages for each cell. Press the
Jog dial
at any time to return to the Charge Monitor screen. The charger signals
when the charging (or discharging) process is complete (if Buzzer is set to ON).
CAUTION:
The Li-Io program menus are to be used ONLY for the charging
and discharging of Li-Io battery packs. The charging of other battery types
using these programs will result in damage to the battery or charger.
CAUTION:
Using a charge rate that is not compatible with the battery
capacities may result in damage or malfunction of the charger or
batteries.
9
LI-IO BALANCE CHARGING
Press the
Mode key
until you reach the 9 main menus, then rotate the
Jog dial
to
locate the PROGRAM SELECT LiIo BATT screen. Press the
Jog dial
to go into this
menu.
Rotate the
Jog dial
to go to the LiIo BALANCE screen and set charging parameters.
The charging amperage
(A)
can be set between 0.1 and 10.0A. Voltage
(B)
is
dependent on the number of cells in series. For example, with Li-Io batteries these
values can be from 3.6V (for 1S batteries) to 21.6V (for 6S batteries).
LiIo BALANCE
5.5A 21.6V(6S)
A
B
C
To select values other than the existing parameters:
• Press the
Jog dial
so the charge current value
(A)
flashes
• Rotate the
Jog dial
to INCREASE OR DECREASE the charge current value
• Press the
Jog dial
to save the value and the voltage value
(B)
flashes
• Rotate the
Jog dial
to INCREASE OR DECREASE the voltage (and # of cells in
series
(C)
)
• Press the
Jog dial
to save the voltage value
If no parameters are flashing, you can rotate the
Jog dial
to select another program
such as CHARGE, FAST CHG, STORAGE or DISCHARGE.
To start charging, press and hold the
Jog dial
for 3 seconds.
10
LI-IO CHARGING
Press the
Mode key
until you reach the 9 main menus, then rotate the
Jog dial
to
locate the PROGRAM SELECT LiIo BATT screen. Press the
Jog dial
to go into this
menu.
Rotate the
Jog dial
to go to the LiIo CHARGE screen and set charging parameters.
The charging amperage
(A)
can be set between 0.1 and 10.0A. Voltage
(B)
is
dependent on the number of cells in series. For example, with Li-Io batteries these
values can be from 3.6V (for 1S batteries) to 21.6V (for 6S batteries).
LiIo CHARGE
4.6A 21.6V(6S)
A
B
C
To select values other than the existing parameters:
• Press the
Jog dial
so the charge current value
(A)
flashes
• Rotate the
Jog dial
to INCREASE OR DECREASE the charge current value
• Press the
Jog dial
to save the value and the voltage value
(B)
flashes
• Rotate the
Jog dial
to INCREASE OR DECREASE the voltage (and # of cells in
series
(C)
)
• Press the
Jog dial
to save the voltage value
If no parameters are flashing, you can rotate the
Jog dial
to select another program
such as BALANCE, FAST CHG, STORAGE or DISCHARGE.
To start charging, press and hold the
Jog dial
for 3 seconds.
CAUTION:
If at any time during the charge process the battery pack becomes
hot or begins to puff, disconnect the battery immediately and discontinue the
charge process as batteries can cause fire, collateral damage and injuries.
11
LI-IO fAST CHARGING
Press the
Mode key
until you reach the 9 main menus, then rotate the
Jog dial
to
locate the PROGRAM SELECT LiIo BATT screen. Press the
Jog dial
to go into this
menu.
Rotate the
Jog dial
to go to the LiIo FAST CHG screen and set charging param-
eters. The charging amperage
(A)
can be set between 0.1 and 10.0A. Voltage
(B)
is
dependent on the number of cells in series. For example, with Li-Io batteries these
values can be from 3.6V (for 1S batteries) to 21.6V (for 6S batteries).
Near the end of a standard charging cycle, the charger switches from Constant Cur-
rent (CC) mode to Constant Voltage (CV) mode to slowly “top off” the current in the
battery as close as possible to the maximum capacity.
In Fast Charge, the CV mode is eliminated in order to greatly shorten the charging
time; however, the final capacity of the battery will be less than what you would get
using the standard charge method.
LiIo FAST CHG
5.0A 21.6V(6S)
A
B
C
To select values other than the existing parameters:
• Press the
Jog dial
so the charge current value
(A)
flashes
• Rotate the
Jog dial
to INCREASE OR DECREASE the charge current value
• Press the
Jog dial
to save the value and the voltage value
(B)
flashes
• Rotate the
Jog dial
to INCREASE OR DECREASE the voltage (and # of cells in
series
(C)
)
• Press the
Jog dial
to save the voltage value
If no parameters are flashing, you can rotate the
Jog dial
to select another program
such as CHARGE, BALANCE, STORAGE or DISCHARGE.
To start charging, press and hold the
Jog dial
for 3 seconds.
12
LI-IO STORAGE CHARGING
Press the
Mode key
until you reach the 9 main menus, then rotate the
Jog dial
to
locate the PROGRAM SELECT LiIo BATT screen. Press the
Jog dial
to go into this
menu.
Rotate the
Jog dial
to go to the LiIo STORAGE screen and set charging parameters.
The charging amperage
(A)
can be set between 0.1 and 10.0A. Voltage
(B)
is
dependent on the number of cells in series. For example, with Li-Io batteries these
values can be from 3.6V (for 1S batteries) to 21.6V (for 6S batteries).
If you don’t plan on using your battery for a long time, it is best to charge (or
discharge) the battery to its optimal storage voltage and capacity.
LiIo STORAGE
2.5A 21.6V(6S)
A
B
C
To select values other than the existing parameters:
• Press the
Jog dial
so the charge current value
(A)
flashes
• Rotate the
Jog dial
to INCREASE OR DECREASE the charge current value
• Press the
Jog dial
to save the value and the voltage value
(B)
flashes
• Rotate the
Jog dial
to INCREASE OR DECREASE the voltage (and # of cells in
series
(C)
)
• Press the
Jog dial
to save the voltage value
If no parameters are flashing, you can rotate the
Jog dial
to select another program
such as CHARGE, BALANCE, FAST CHG or DISCHARGE.
To start charging, press and hold the
Jog dial
for 3 seconds.
1
SELF TEST AND PROGRAM SELECT SCREENS
LI-fE
2
LI-FE BATTERIES
3
LI-FE BALANCE CHARGING
4
LI-FE CHARGING
5
LI-FE FAST CHARGING
6
LI-FE STORAGE CHARGING
7
LI-FE DISCHARGE
LI-IO
8
LI-IO BATTERIES
9
LI-IO BALANCE CHARGING
10
LI-IO CHARGING
11
LI-IO FAST CHARGING
12
LI-IO STORAGE CHARGING
13
LI-IO DISCHARGE
LI-PO
14
LI-PO BATTERIES
15
LI-PO BALANCE CHARGING
16
LI-PO CHARGING
17
LI-PO FAST CHARGING
18
LI-PO STORAGE CHARGING
19
LI-PO DISCHARGE
NI-MH
20
NI-MH BATTERIES
21
NI-MH CHARGING
22
NI-MH AUTO CHARGING
23
NI-MH DISCHARGE
24
NI-MH RE-PEAK CHARGING
25
NI-MH CYCLE CHARGING
NI-Cd
26
NI-CD BATTERIES
27
NI-CD CHARGING
28
NI-CD AUTO CHARGING
29
NI-CD DISCHARGE
30
NI-CD RE-PEAK CHARGING
31
NI-CD CYCLE CHARGING
PB
32
PB BATTERIES
33
PB CHARGING
34
PB DISCHARGE
PROGRAMMING ANd OPERATIONS
35
BATTERY MEMORY
36
SYSTEM SET
a
REST TIME
b
SAFETY TIMER
c
CAPACITY CUTOFF
d
KEY BEEP/BUZZER
e
INPUT POWER LOW CUTOFF
f
EXTERNAL AND INTERNAL TEMPERATURES
g
RESET FACTORY SETTINGS
h
VERSION
37
LI BATTERY VOLTAGE CHECKER OPERATION -
USING THE BALANCE ADAPTER PORT
38
USB ACCESSORY CHARGER OPERATION
(COMPATIBLE WITH iPhone AND iPod DEVICES)
39
TROUBLESHOOTING GUIDE
Press the
Mode key
until you reach the 9 main menus, then rotate the
Jog dial
to
locate the PROGRAM SELECT LiIo BATT screen. Press the
Jog dial
to go into this
menu.
Rotate the
Jog dial
to go to the LiIo DISCHARGE screen and set discharging param-
eters. The discharging amperage
(A)
can be set between 0.1 and 5.0A. Voltage
(B)
is dependent on the number of cells in series. For example, with Li-Io batteries these
values can be from 3.6V (for 1S batteries) to 21.6V (for 6S batteries).
A battery’s capacity can be verified by discharging it to its minimum voltage level
and measuring the current as the battery is discharged.
LiIo DISCHARGE
2.0A 21.6V(6S)
A
B
C
To select values other than the existing parameters:
• Press the
Jog dial
so the discharge current value
(A)
flashes
• Rotate the
Jog dial
to INCREASE OR DECREASE the discharge current value
• Press the
Jog dial
to save the value and the voltage value
(B)
flashes
• Rotate the
Jog dial
to INCREASE OR DECREASE the voltage (and # of cells in
series
(C)
)
• Press the
Jog dial
to save the voltage value
If no parameters are flashing, you can rotate the
Jog dial
to select another program
such as CHARGE, BALANCE, FAST CHG or STORAGE.
To start discharging, press and hold the
Jog dial
for 3 seconds.
13
LI-IO dISCHARGING
14
LI-PO BATTERIES
Press the
Mode key
until you reach the 9 main menus, then rotate the
Jog dial
to
locate the PROGRAM SELECT LiPo BATT screen. Press the
Jog dial
to select LiPo.
Rotate the
Jog dial
to go to one of the control screens (BALANCE, CHARGE, FAST
CHG, STORAGE or DISCHARGE) to do what your battery needs.
Correctly connect your lithium battery to the charger (charging connector first and
balancing connector second). Press the
Jog dial
and adjust the charging param-
eters as needed. Press and hold the
Jog dial
(approximately 3 seconds) until the
screen changes to start the battery check/charge sequence.
R: 3SER
S:3SER
CONFIRM (ENTER)
A
When the charge cycle starts, the
charger compares the battery to the
charger settings. The screen will show
the battery and your settings
information. If the information after R: (charger) and S: (settings)
(A)
does not match,
press the
Mode key
and change the lithium battery charging parameters as
needed. If the R: information matches S:, press the
Jog dial
to confirm.
After confirmation, charging starts and information will show on the LCD screen
(information may vary).
LI 3S 2.0A 12.59V
BAL 022:43 01082
f
E
B C
d
A
A.
A Li-Po battery pack is
balance charging
B.
Battery pack has 3 cells in
series
C.
Charging rate is 2.0A (2000mAh)
d.
Voltage being applied to the battery is currently 12.59V
E.
Present charge level of the battery is 1082mAh
f.
Time elapsed since the charge process started is 22:43
During charging, the
Jog dial
can be rotated counterclockwise to show several
parameter messages on the LCD screen, including: End Voltage, Input Power Volt-
age, External & Internal Temperature, Temperature Cutoff, Safety Timer Status and
Capacity Cutoff.
Rotate the
Jog dial
clockwise to show the charge voltages for each cell. Press the
Jog dial
at any time to return to the Charge Monitor screen. The charger signals
when the charging (or discharging) process is complete (if Buzzer is set to ON).
CAUTION:
The Li-Po program menus are to be used ONLY for the
charging and discharging of Li-Po battery packs. The charging of other
battery types using these programs will result in damage to the battery or
charger.
CAUTION:
Using a charge rate that is not compatible with the battery
capacities may result in damage or malfunction of the charger or
batteries.
15
LI-PO BALANCE CHARGING
Press the
Mode key
until you reach the 9 main menus, then rotate the
Jog dial
to
locate the PROGRAM SELECT LiPo BATT screen. Press the
Jog dial
to go into this
menu.
Rotate the
Jog dial
to go to the LiPo BALANCE screen and set charging param-
eters. The charging amperage
(A)
can be set between 0.1 and 10.0A. Voltage
(B)
is
dependent on the number of cells in series. For example, with Li-Po batteries these
values can be from 3.7V (for 1S batteries) to 22.2V (for 6S batteries).
LiPo BALANCE
5.5A 22.2V(6S)
A
B
C
To select values other than the existing parameters:
• Press the
Jog dial
so the charge current value
(A)
flashes
• Rotate the
Jog dial
to INCREASE OR DECREASE the charge current value
• Press the
Jog dial
to save the value and the voltage value
(B)
flashes
• Rotate the
Jog dial
to INCREASE OR DECREASE the voltage (and # of cells in
series
(C)
)
• Press the
Jog dial
to save the voltage value
If no parameters are flashing, you can rotate the
Jog dial
to select another program
such as CHARGE, FAST CHG, STORAGE or DISCHARGE.
To start charging, press and hold the
Jog dial
for 3 seconds.
TABLE Of CONTENTS
16
LI-PO CHARGING
Press the
Mode key
until you reach the 9 main menus, then rotate the
Jog dial
to
locate the PROGRAM SELECT LiPo BATT screen. Press the
Jog dial
to go into this
menu.
Rotate the
Jog dial
to go to the LiPo CHARGE screen and set charging parameters.
The charging amperage
(A)
can be set between 0.1 and 10.0A. Voltage
(B)
is
dependent on the number of cells in series. For example, with Li-Po batteries these
values can be from 3.7V (for 1S batteries) to 22.2V (for 6S batteries).
LiPo CHARGE
4.6A 22.2V(6S)
A
B
C
To select values other than the existing parameters:
• Press the
Jog dial
so the charge current value
(A)
flashes
• Rotate the
Jog dial
to INCREASE OR DECREASE the charge current value
• Press the
Jog dial
to save the value and the voltage value
(B)
flashes
• Rotate the
Jog dial
to INCREASE OR DECREASE the voltage (and # of cells in
series
(C)
)
• Press the
Jog dial
to save the voltage value
If no parameters are flashing, you can rotate the
Jog dial
to select another program
such as BALANCE, FAST CHG, STORAGE or DISCHARGE.
To start charging, press and hold the
Jog dial
for 3 seconds.
CAUTION:
If at any time during the charge process the battery pack becomes
hot or begins to puff, disconnect the battery immediately and discontinue the
charge process as batteries can cause fire, collateral damage and injuries.
LITHIUM BATTERIES (Li-fe)
LITHIUM BATTERIES (Li-Po)
Pb BATTERIES
Ni-Cd BATTERIES
Ni-MH BATTERIES
LITHIUM BATTERIES (Li-Ion)
BATTERy MEMORy
LITHIUM BATTERy METER
SySTEM SET
