background image

MF …56

MC • Edition 04.19 • No

. 278 349

1 … 56

The target group of this manual is qualified personnel of the 

gas safety and regulating technology. Due to their specialist 

training, knowledge and experience, they should be capable 

of evaluating the work assigned to them and recognising 

possible dangers. Only they are permitted to carry out as

-

sembly, commissioning, settings and maintenance on the 

devices in compliance with the recognised rules for occupa

-

tional safety.

Instructions

FRM 100065 - 100080 - 250065 - 250080

2. Warnings                         

Never carry out work as long as gas 

pressure or voltage is applied. Avoid 

open fire. Please observe public regula-

tions. 

The device must be protected from vi-

brations and mechanical impacts.

All adjustments and settings should only 

be performed in accordance with the 

instruction manuals of the connected 

machines. 

The recognised occupational safety 

rules and accident prevention regula-

tions must be observed and, if neces-

sary, personal protective measures must 

be taken.

Connected line systems must be free 

from dirt and contamination.

Hang this instruction manual in a readily visible place 

inside the installation room! Do not carry out any work 

until you have read the safety instructions of this in-

struction manual and are qualified to do so.

The device may only be operated in 

compliance with the operating condi-

tions stated on the type plate.

Prior to assembly, the device must be 

inspected for transport damage.

The device must not be used in areas 

with increased seismic risk.

Protection from environmental impacts 

and weather conditions (corrosion, rain, 

snow, icing, humidity (e.g. by conden-

sation), mould, UV radiation, harmful 

insects, poisonous, corrosive solutions/

liquids (e.g. cutting and cooling fluids

), 

must be guaranteed. Depending on the 

installation site, it may be necessary to 

take protective measures.

The device must not be exposed to open 

fire. Protection against lightning strikes 

must be guaranteed.

2.1 General warnings                         

1. Target group 

 

 

 

 

                    

Explanation of the symbols

1, 2, 3,...    =  

Order of 

  action

•        =  

Instruction

Summary of Contents for 273061

























































Reviews: