background image

 

EXCEL-FIRE

 

VENTED GAS STOVE

 

INSTRUCTIONS MANUAL 

 

 
 

 

 

 

WARNING:

 If the information in these 

instructions is not followed exactly, a fire or 
explosion may result causing property 
damage, personal injury or loss of life.

 

FOR YOUR SAFETY:

 Do not store or use 

gasoline or other flammable vapours and 
liquids in the vicinity of this or any other 
appliance. 

Installation and service must be performed 
by a qualified installer, service agency or the 
gas supplier. 

WHAT TO DO IF YOU SMELL GAS: 

• 

Do not try to light any appliance. 

• 

Do not touch any electric switch; do not use 
any phone in your building. 

• 

Immediately call your gas supplier from 
neighbour’s phone. Follow the gas supplier’s 
instructions. 

• 

If you cannot reach your gas supplier, call the 
fire department. 

THE INSTALLATION MUST CONFORM WITH LOCAL CODES OR, IN THE ABSENCE OF 

LOCAL CODES, WITH THE CURRENT 

NATIONAL FUEL GAS CODE

 

ANSI Z223.1

 (USA) 

OR THE CURRENT 

CAN/CGA B149

 

INSTALLATION CODES 

(CANADA). 

PLEASE KEEP THIS INSTRUCTIONS MANUAL 

FOR FUTURE REFERENCE 

mai2000/45052A 

Summary of Contents for EXCEL-FIRE
















Reviews: