background image

 

 
 
 
 
 
 

 

Art. no. 0541908109030 

V16 G27 

 

Pelletto III  

419.08 / 434.08 

 

Equipment sheet - Pellett Stove 

 

  

Important manufacturer’s instructions

!

 

Please observe the following instructions:  

Quality of wood pellets:  

Depending on the manufacturer there are light, dark, shorter and longer pellets. And the quality of one delivery may 
differ from another even from the same supplier. The standards for wood pellets are becoming more and more strict 
but wood is wood and has its own characteristics regarding ash and clinker.  

Cleaning requirements:  

As  soon  as  you  find  ash  and  clinker  deposits  in  the  cold  combustion  pot,  it  must  be  cleaned. 

See  operating 

instructions! 

If this is not done, there will be more and more clinker. Then the device will no longer be able to ignite 

properly. Pellets may pile up in the combustion pot. In extreme cases, this can reach all the way back to the pellet 
chute.  Backfire  in  the  pellet  container  and  smouldering  in  the  pellet  tank  might  possibly  result. 

This  will  destroy 

your device and is not covered by the guarantee.

  

For maximum working life:  

  Arrange for commissioning by your trained stove supplier.  

  Observe the daily check as described and more frequently if you have received new pellet deliveries or when 

the device is brought back into use after the summer.  

 

Carefully read through all the operating instructions and retain them.

 

 
 Type number: 

 

Summary of Contents for Pelletto III 419.08
















Reviews: