background image

Yardley Single Ottoman

Assembly Instructions

Need assistance?

Call: 0344 292 0000

Dimensions mm Length Width

Height

Single

2040

1010

910

Approximate time to 
assemble this product

Retain these instructions 
for future reference

2 x people recommended to 
assemble this product

Do not discard any of the 

packaging until you have 

checked that you have all the 

parts and the pack of fixings.

You will require a cross 
head screwdriver

Helpful advise before you begin:

1.

   We suggest you spend a short time reading through this leaflet 

and then follow the simple step by step instructions.

2.

   If you follow the instructions carefully the end result should be 

worth the effort.

3.

   Do not discard any of the packaging until you have checked that 

you have all the parts and the pack of fittings.

4.

  Assemble this product on a carpet.

5.

   To ensure an easier assembly, we strongly advise that all fittings 

are only finger tightened during initial assembly. Only upon 

completion of the assembly should all fixing points be fully 

tightened.

6.

   We recommend a periodic check on all fixing points to make 

sure they remain fully tightened.

7.

  Keep glue and fittings out of children’s reach.

8.

   Do not use any other tools other than those recommended to 

build this product.

9.

   Please do not use substitute parts. Use only additional or 

replacement parts supplied by Dreams Ltd.

10.

   In the unlikely event that this product has missing or damaged 

parts, please call 0344 292 0000 to obtain spares.

Page 1 of 7

1/2

Summary of Contents for Yardley Single Ottoman








Reviews: