Partial Open
PUS
H T
O O
PER
ATE
tech
nici
an use
only
Lock Plate
Powe
r
Manu
al Release
Reset
1
Motor
2
Motor
3
Neu
tral
4
24V
AC
5
Limit
6
Spar
e
7
Limit
8
COM
3
2
1
6
5
4
9
8
7
#
0
*
Radio Receiver
1
ON
2
3
4
5
6
7
8
1
ON
2
3
4
QUICKSTART “BASIC” GUIDELINES FOR MODEL 9000 - FRONT INSTALLATION MOUNTED ON A CONCRETE PAD “FULL OPEN”
Copyright 2018 DoorKing, Inc. All rights reserved.
9000-066-J-8-18
Use 3/4-inch conduit
with sweeps.
3-Wire
Below ground depth of the concrete pad is
determined by soil conditions and local building
codes (reinfor
ced concrete recommended).
Switch
1
in ON
position
.
Use (4) 3/
8” x 2” Sleeve Anchors
(Not
supplied).
Loop
Conduit
AC Power
Conduit
Concrete
Pad
Opening
Direction
Concrete pad
MUST be level!
Chain Bracket
Chain, Conduit Area and Concrete
4” minimum
above ground
.
3.5”
4.5”
13.5”
24”
24”
Conduit Area
Operator Chassis
Idler
Wheel
Center
Positio
n
Botto
m
Positio
n
Idler Wheel
Top Position
Center
of
concrete
pad
Concrete Pad
SW
1
1
234567
8
ON
Opening
Direction
Switch
1
in OFF
position
.
SW
1
1
2
3
4
5
6
7
8
ON
Loop Detectors
Radio Receiver
B
B
B
A
E
D
C
Not included - Refer to the Installation/Owner’s manual
for more information about DoorKing’s Plug-In loop
detectors. DoorKing highly recommends that loops and
loop detectors are installed with this slide gate operator.
DoorKing offers a free “Loop and Loop-Detectors
Information Manual” PDF located at DoorKing’s web
site for more information. www.doorking.com
C
Not included - Refer to a specific Radio Receiver
Manual (available from www.doorking.com) for more
information on radio receivers and antenna installation.
(See reverse side for wiring)
High Voltage Connection
Tip: It is recommended that a surge suppressor be
installed on the input high voltage power line.
GATE OPERATOR MUST BE PROPERLY GROUNDED!!
Adjust the 2 limit nuts by depressing the lock plate and spin nuts to
desired open and closed gate positions. After adjusting, make sure
the lock-plate is engaged in the slots on the limit-nuts to prevent
them from rotating.
Note: Partial Open Feature is optional and not used for a fully
opening gate, see manual for more information.
Adjust the chain nuts to tighten the chain. The chain
should sag no more than one (1) inch per 10 feet of
chain travel. Do not over tighten the chain.
Adjustment of Limit Switches
Chain Adjustment
Model 9000 is intended for
installation only on sliding
gates used for vehicles.
Pedestrians must be supplied with
a separate access opening.
For complete safety, installation
and adjustment of operator
instructions, please refer to the
Series 9000 Installation/Owner’s
manual.
A
E
D
Neutral
Hot
115 VAC
Chassis
Ground
Input Power Line:
White - Neutral
Black - 115 VAC Hot
Green - Chassis Ground
DANGER
HIGH VOLTAGE
DIP-Switches
SW 1
1.
Opening Direction
(See Illustration)
2. OFF
3.
ON
4.
ON
5. OFF
6. OFF
7. OFF
8. OFF
1. OFF
2. OFF
3.
ON
4. OFF
Auto-Close Timer
Adjust
1 to 23 sec.
SW 2
4” minimum
space
between the
gate and
operator
chassis.
Gate
4”
TIME
DELAY
Chain brackets MUST be
mounted so the chain
remains the same height
as it is on the idler wheels!
Operator and chain
MUST be parallel to gate!
Chain bracket MUST line
up with chain idler wheels!
Two 115 VAC
Convenience Outlets
For access control and safety device AC power.
1 23
Typical Single Operator Settings
DO NOT
power up and cycle the
operator until the “DIP-Switches”
and the “Limit Switches” have
been adjusted. Damage could
occur to the gate and operator.
Note: “Optional” High
Voltage Kit black and
white wires connect
the same as shown.
See High Voltage Kit
instruction sheet for
more information.
(See reverse side for
more information).
120 S. Glasgow Avenue
Inglewood, California 90301
U.S.A.
Warning Signs
Permanently mount signs on BOTH sides of the
gate area and make sure they are easily visible.
Entrapment Protection must be provided for the gate
system where the risk of entrapment or obstruction exists.
The operator will NOT run without one or more monitored
type B1 or B2 external entrapment protection devices in
EACH direction of gate travel (minimum of 2 external
devices required). See manual for more information.
UL 325 August
2018 Standard
