background image

Thank you very much for choosing Daviteq Wireless Sensors. We are the leading wireless sensor manufacturer in the

World. We have a wide range of wireless sensors which support different connectivity like LoRaWAN, Sigfox, Sub-GHz,
NB-IoT...Please find out more information at 

this link

.

This manual is applied to the following products

Item code

HW Version

Firmware Version

Remarks

WSLRW-LPC-01

1.0

1.0

 

Information Changes in this version v.s previous version

Item

Changes

Changed by

Changed Date

Approved by

Approved Date

1

Initial version

P.N.Diep

09-05-2022

N.V.Loc

28-05-2022

To use this product, please refer step by step to the below instructions.

Operating Principle

Uplink Payload

Battery

Connect to Gateway

Installation

Troubleshooting

Configuration

Calibration

Specification

Warranty and Support

WSLRW-LPC is a LoRaWAN sensor with a built-in advanced Lidar sensor to detect and count people. It can count the

people walking thru a gate in 2-way with an accuracy higher than 95%. This sensor utilizes lidar technology, which is

not affected by temperature, humidity, and RF noise and is less affected by ambient light...

Manual for LoRaWAN Lidar People
Counter - WSLRW-LPC | FW 1.0

1.  Quick Guide

Reading time: 10 minutes

Finish this part so you can understand and put the sensor in operation with the default configuration from the

factory.

1.1 What is the LoRaWAN Lidar People Counter sensor and its
principle of operation?

Summary of Contents for WSLRW-LPC















Reviews: