CRUZBIKE Sofrider v2 Assembly Instructions Manual Download | Manualshive

Page: 1 / 11

background image

Cruzbike Sofrider v2 Assembly Instructions - 3/1/2011

Cruzbike Sofrider v2 Assembly page 1 of 11

Assembly Instructions for the

Cruzbike Sofrider

These are assembly instructions only.

Please read the Cruzbike Owner’s Manual for important safety

information and riding instructions.

A Cruzbike Owners support forum is located at:

http://www.cruzbike.com/forums/

1
2
3
...
»

Summary of Contents for Sofrider v2












Reviews:

No comments

Related manuals for Sofrider v2

Brand: FAZUA Pages: 63

Brand: PACIFIC CYCLES Pages: 32

Brand: BAFANG Pages: 47

Brand: satmap Pages: 4

HEADSHOK FATTY DLR80

Brand: Cannondale Pages: 4

Brand: Topeak Pages: 2

Brand: SRAM Pages: 20

Brand: Velo Machine Pages: 2

Brand: e-Joe Pages: 16

Dummy Rail Collar

Brand: Surly Pages: 4

Nexus INTER 5E SG-C7000-5C

Brand: Shimano Pages: 85

VACUUM Ahead cap base

Brand: Fidlock Pages: 2

Brand: Bottecchia Pages: 17

Brand: lovelec Pages: 4

Brand: SmarTrike Pages: 8

Brand: SmarTrike Pages: 12

Brand: SmarTrike Pages: 20

Brand: FLOATERHOIST Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands