manualshive.com logo in svg
background image

#

Cisco Systems, Inc.

www.cisco.com

 

Cisco Aironet 2.4 GHz and 5 GHz 
Dual-Band Polarization-Diverse Directional 
Array Antenna (AIR-ANT2566D4M-R)

This document describes the Cisco Aironet 2.4 GHz and 5 GHz Dual-Band Polarization-Diverse Directional Array Antenna 
(AIR-ANT2566D4M-R), and provides electrical specifications and mounting instructions. 

The AIR-ANT2566D4M-R antenna is a four-port polarization-diverse array that operates over the 2.4 GHz and 5 GHz Wi-Fi 
bands. It ships with an articulating mount for use on flat surfaces and masts, and is adjustable in both horizontal and vertical 
planes. The radome can be painted using commonly available non-conductive spray paints, such as Krylon or Rust-Oleum. 

The antenna is designed for use in indoor and outdoor environments with an approved Cisco Aironet access point that requires 
four dual-band antennas. 

The following information is provided in this document:

Technical Specifications

Azimuth and Elevation Radiation Patterns

Safety Precautions

Installation Notes

Contents of the Antenna and Bracket Kit

Dimensions of the Antenna and Brackets

Installing the Antenna

Obtain Documentation and Submit a Service Request

Содержание Aironet AIR-ANT2566D4M-R



















Отзывы: