Metal
Rod
Brass
Extension
Brass
Extension Nut
Nozzle
Adapter
Nozzle
6-8135
Dripless Shut-off
Cierre antigoteo
Arrêt anti-goutte
6-4608
Pressure Relief Valve
Válvula de descarga de
presión
Soupape de
décompression
WARNING
3. Pre-Use Check
1)
Do:
Check tightness of hose nut to be sure hose is securely attached to the tank outlet.
2)
Do:
Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are
found, replace hose before using. Replace with original manufacturer’s parts only.
3)
Do:
Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and
exterior of tank for signs of deterioration of body and bottom. Any sign of deterioration indicates
possible tank weakening and could result in explosive bursting under pressure. If any of these
signs are found, discard tank immediately and replace. Do not attempt to patch leaks, etc., as this
could result in serious injury.
4)
Do:
Follow Filling, Pressurizing and Spraying Instructions, except use water only
(Pump plunger 10-20 strokes and inspect for leaks).
5)
Do:
Direct shut-off away from you and open to make sure discharge is not clogged.
6)
Do:
If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank,
and proceed with Filling, Pressurizing and Spraying Instructions.
7)
Do:
Inspect all metal parts including the wand, nozzle and fittings for rust, corrosion and pitting.
If any of these conditions are found, replace affected part with original manufacturer’s part
before using.
4. Filling
1)
Do:
Turn pump handle counterclockwise and remove pump
2)
Do:
Prepare spray solution following all directions and safety warnings on chemical label.
3)
Do:
Fill tank to no more than the proper gallon marker. Do NOT: over fill to accommodate pump.
4)
Do:
Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and
tighten securely.
9. Care, Storage and Maintenance
1)
Do:
Follow chemical manufacture’s instructions for cleaning. Rinse thoroughly with
recommended solvent. Follow Filling, Pressurizing and Spraying Instructions, except pump unit
only 8-10 strokes. Be sure that the wand and nozzle are thoroughly rinsed after each use.
2)
Do:
Open shut-off and allow recommended solvent to run through discharge assembly.
3)
Do:
Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.
4)
Do:
Store sprayer tank upside down, with pump removed, in a warm dry location.
5)
Do:
Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening
in cover.
011534-7 (A) R1020
P.O. Box 549 700 Ellicott St.
Batavia, NY 14021-0549 U.S.A.
1-800-950-4458 www.chapinmfg.com
1. Hose to Tank
Discharge/ Assembly
• Make sure white outlet tube is attached to outlet tube adapter (Fig. 1A).
• Insert the outlet tube portion of the discharge assembly into the tank adapter (Fig. 1B).
• Proper placement of white outlet tube (Fig. 1C).
• Firmly insert the outlet tube adapter into the tank adapter (Fig. 1D) Lining up tab with notches on
the tank adapter.
• Firmly tighten the retaining nut to the tank adapter (Fig. 1E).
Discharge
Assembly
1B
Outlet
Tube
1E
Retaining Nut -
Securely tightened.
1C
1D
No
Gap
Tank
Adapter
Outlet Tube
Adapter
Tab/
Notch
1A
Outlet Tube
Adapter
Outlet
Tube
Parts, Piezas, Pièces
6-4604
Repair Parts Kit Gaskets and Seals (not included),
Juego de piezas de reparación, empaquetaduras y juntas (no incluido)
Kit de pièces de réparation, joints et garniture d’étanchéité (non inclus)
Note:
Your particular sprayer may not include all parts pictured above.
Nota:
Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.
Remarque :
Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
Congratulations!
You have just purchased a quality Chapin product.
Register Your Sprayer Online @ www.chapinmfg.com Questions? Do Not Return To Store.
Call us @ 1-800-950-4458 or www.chapinmfg.com
6-6093
Hose Black
Manguera para trabajos
pesados Negro
Tuyau pour service
intense Noir
6. Lock Off
For safety lock-off feature (no-spraying),
push trigger forward and rotate locking
mechanism into lock-off position(Fig. 6A).
6-8136
Valve Seat Kit
Kit de la válvula
Ensemble de soupape
6A
6A
Lock
Trigger
WARNING: Improper use or failure to follow instructions can result in explosive failure causing serious
eye or other injury.
For safe use of this product you must read and follow all instructions. Do not leave a
pressurized sprayer in the hot sun. Heat can cause pressure build-up resulting in possible explosion. Do not
store or leave solution in tank after use. Always wear goggles, gloves, long sleeve shirt, long pants and full foot
protection when spraying. Never use any tool to remove pump if there is pressure in sprayer. Never stand with
face or body over top of tank when pumping or loosening pump to prevent ejecting pump assembly and/or
solution from striking and injuring you. Never pressurize sprayer by any means other than the original pump.
Do not attempt to modify this sprayer. Replace parts only with manufacturer’s original parts.
This sprayer is
intended for Acetone only. Acetone is extremely flammable. This Acetone sprayer is intended for trained
professionals only. Not intended for the retail trade. Always read and follow chemical manufacturer’s
instructions before use with this sprayer as some chemicals may be hazardous when used with this sprayer.
Sk-1169-1
6-1929
Nozzle & Brass Adapter
Tobera
Buse
5. Pressurizing and Spraying
Do:
Turn handle
clockwise to tighten.
Push handle down,
turn 1/4 turn counter-
clockwise to release.
Do:
Pump until you
feel resistance.
Do:
Push handle, down, turn 1/4
turn clockwise to lock. Begin
spraying. Re-pump sprayer as
required to maintain spray force.
5A
5A
5C
5C
5B
5B
7. To Release Pressure
1) Your sprayer is equipped with a pressure
relief/release valve (Fig. 7A). To release
pressure lift and hold the cap until air is
completely exhausted, or, turn the valve slowly
counter-clockwise until you hear air escaping
and wait air is completely exhausted (Fig. 7B).
2)
Do:
Stay away from the sprayer until all air
has escaped.
7A
7A
8. Wand Dock Clip
7B
7B
Choose the holder that fits your wand.
301630-2
Pump Assembly
Asamblea de la
bomba
Assemblée de pompe
2. Extension wand and Nozzle Assembly
To attach nozzle directly to shut-off, unthread brass extension nut and metal rod. Assemble
valve seat (included), nozzle adapter and nozzle to the shut-off as shown in figure 2C. Note
orientation of valve seat. It will leak if assembled incorrectly.
Metal Rod
Shut-off to wand to nozzle assembly
Shut-off to nozzle assembly with included valve seat
2A
Metal Rod
Valve Seat
Nozzle Adapter
Nozzle
2B
2C
The dripless shut-off
comes assembled as
shown in figure 2A.
