NOTE: Please read instructions before drilling any
holes or marking out hole centres.
Mark both sides of the door using the template (flip
template over to mark other side).
DO NOT drill right through the door as alignment
issues will occur. Only drill to centre.
There are five stages to fitting the Mortice Case:
Stage 1: Mark drilling positions for lock case.
Stage 2: Mark drilling positions for door furniture to
be installed
Stage 3: Prepare door by mortising and drilling holes.
Stage 4: Fit lock & door furniture.
Stage 5: Fit striker.
Stage 1 - Mark Drilling Positions
for Lock Case
1. Mark chosen height of lock on face of door.
Height is normally measured to centre of square
spindle (Hole 9).
2. Mark ‘Height Line’ at top of template 57.5mm
(2-9/32”) above Hole 9 or 121.5mm (4-25/32”) above
Hole 10 on front edge and both faces of door.
3. Make a vertical centre line on front edge of door.
Universal Hole Positions
Hole #
Hole Diameter
Depth
1 - 6
19mm
3/4”
77mm
3”
7 & 8
2.5mm
3/32”
25mm
1”
Indicator Lock Hole Positions
Hole # Hole Diameter
Depth
Door Side
9 - 11
19mm
3/4” To Centre of Door
Both
12 or 13 6.5mm
1/4” To Centre of Door
Both
14 & 15 10mm 25/64” To Centre of Door
Both
4. Align top edge of template with height line and
arrows to vertical centre line.
5. Mark universal hole positions (Holes 1-8) for lock
case using a sharp nail or pencil.
1
2
3
4
5
6
8
7
FOLD HERE AND PLACE ON CORNER OF DOOR
134
mm
(5-9/32”)
9
12
12
12
12
16
13
14
15
10
11
Backset 56
mm
(2-13/64”)
CL100ZA525
02.2018
HEIGHT LINE
DRILLING TEMPLA
TE FOR CL100 MOR
TICE
READ FITTING INSTRUCTIONS
121.5
mm
(4-25/32”)
20
mm
(25/32”)
57.5
mm
(2-1/4”)
STRIKER TEMPLA
TE
Ø10
mm
(25/64”)
4x Ø
6.5
mm
(1/4”)
6
mm
(15/64”)
Stage 2 - Mark Drilling Positions
for Door Furniture
1. Highlight correct drilling options required
for handle and use a sharp nail or pencil to
mark required hole centres. Holes 12-13 to be
vertical or diagonal fixing holes at the correct
hole centres to suit the lever handles being
used.
Stage 3 - Mortice & Drill Holes
DO NOT drill right through the door.
Alignment issues will occur. Drill to centre on
both sides for through holes. Check Stage 2
chart for hole depth.
1. Drill Holes 1-6. Make sure drilled holes are
straight and level.
2. Chisel out remaining wood between holes indicated
in shaded area on template to create a slot.
Note: Maximum slot length not to exceed 134mm
(5-9/32”).
3. Drill Holes 7 and 8.
4. Remove face plate from lock case and temporarily
screw lock case in place. Mark around outside edge
of inner forend then remove lock.
5. Router out marked area to a depth of 7mm (9/32”).
Important: Recess of front section must be routered
flat and even. Long term damage will occur if not
done correctly.
6. Drill Holes 9 to 11.
7. Remove remaining wood from oval shaped slot
between Holes 10 and 11.
8. Drill holes for fixing handles using marks from
Stage 2.
Height
line
Centre
line
Front
edge
of
door
Face
plate
Inner
forend
Drilled
holes
7 & 8
Router
out 7mm
(9/32”)
INDICATOR LOCK Fitting Instructions
1
ST
AGE
ST
AGE
2
ST
AGE
3
