background image

 

Installation Manual of Classic Solar Modules

 

 

 

www.canadiansolar.com       

Rev IM/GN-CM-EN/1.0          Copyright© October, 2020 Canadian Solar Inc.        0

 

CONTENTS 

1.0    GENERAL INFORMATION ......................................................................................................................... 1

 

1.1    INSTALLATION MANUAL DISCLAIMER ..................................................................................................... 1

 

1.2    LIMITATION OF LIABILITY ........................................................................................................................ 1

 

2.0    SAFETY PRECAUTIONS ............................................................................................................................. 1

 

3.0    MECHANICAL / ELECTRICAL SPECIFICATIONS ......................................................................................... 2

 

4.0    UNPACKING AND STORAGE .................................................................................................................... 4

 

5.0    MODULE INSTALLATION .......................................................................................................................... 4

 

5.1    MODULE WIRING .................................................................................................................................... 7

 

5.2      GROUNDING .......................................................................................................................................... 8

 

6.0    MOUNTING INSTRUCTIONS .................................................................................................................... 8

 

6.1    MOUNTING METHOD: BOLTING ............................................................................................................. 9

 

7.0    MAINTENANCE ...................................................................................................................................... 11

 

ANNEX A: ALTERNATIVE MOUNTING METHODS WITH SINGLE-AXIS TRACKER .......................................... 13

 

ANNEX B : MECHANICAL AND ELECTRICAL RATINGS ................................................................................... 14

 

ANNEX C: Module Cleaning Guidelines ........................................................................................................ 16

 

AMENDED EDITIONS AND DATES ................................................................................................................... 17

 

 
 
 
 
 
 
 
 

Summary of Contents for CS5AH-180M



















Reviews: