Can-Am Outlander 500 2008 Operator'S Manual Download

Page: 1 / 152

Vmo2008-001_OUTLANDER568_219000476_ANG.FH10 Thu Mar 29 14:53:06 2007 Page 1

Composite

CY CMY

THIS VEHICLE CAN BE HAZARDOUS TO OPERATE.

A collision or rollover can occur quickly, even during

routine maneuvers such as turning and driving on hills

or over obstacles, if you fail to take proper precautions.

SEVERE INJURY OR DEATH

can result if

you do not follow these instructions:

BEFORE YOU OPERATE THIS VEHICLE, READ

THIS

OPERATORS GUIDE

AND ALL ON-

PRODUCT LABELS.

 NEVER OPERATE THIS VEHICLE WITHOUT

PROPER INSTRUCTIONS.

Beginners should

complete a certified training course.

NEVER CARRY A PASSENGER.

You increase

your risk of losing control if you carry a passenger.

 NEVER OPERATE THIS VEHICLE ON A PAVED

SURFACE.

You increase your risk of losing control

if you operate this vehicle on pavement.

 NEVER OPERATE THIS VEHICLE ON PUBLIC

ROADS.

You can collide with another vehicle if you

operate this vehicle on a public road.

 ALWAYS WEAR AN APPROVED HELMET,

eye protection, and protective clothing.

 NEVER CONSUME ALCOHOL OR DRUGS

before or while operating this vehicle.

 NEVER OPERATE THIS VEHICLE AT EXCESSIVE

SPEEDS.

You increase your risk of losing control

if you operate this vehicle at speeds too fast for the

terrain, visibility conditions, or your experience.

NEVER ATTEMPT WHEELIES, JUMPS, OR OTHER

STUNTS.

WARNING

Read this guide thoroughly. It contains important safety information.

Minimum recommended operators age: 16 years old. Do not remove this Operators Guide from the vehicle.

WARNING

® AND THE BRP LOGO ARE TRADEMARKS OF BOMBARDIER RECREATIONAL PRODUCTS INC. OR ITS AFFILIATES.

219 000 476

OPERATORS GUIDE, OUTLANDER 500, 650, 800 / ENGLISH

GUIDE DU CONDUCTEUR, OUTLANDER 500, 650, 800 / ANGLAIS

FAIT AU / MADE IN CANADA

U/M:P.C.

2 1 9 0 0 0 4 7 6

Includes

Safety, Vehicle

and

Maintenance Information

Operators

Guide

OUTLANDER

500/650/800

OUTLANDER

500/650/800

Summary of Contents for Outlander 500 2008

























































































































































Search results

Summary of Contents for Outlander 500 2008

Reviews:

Related manuals for Outlander 500 2008

Brands by name

Popular brands

Can-Am Outlander 500 2008, Operator'S Manual

Search results

Summary of Contents for Outlander 500 2008

Reviews:

Related manuals for Outlander 500 2008

Brands by name

Popular brands