background image

BRPRC108HE 

REV B 

 

2/2020

 

 

 

 

OWNER’S MANUAL FOR:  

44” Rough Cut Mower  

w/ Elec. Clutch Blade Engagement 

This machine is intended for use behind a tractor, ATV or UTV  

to cut field, brush and saplings up to 2” thick. 

 

 

Any Questions, Comments, Problems or Parts Orders 

Call BRAVE Product Support 1-800-350-8739

 

 

 

          WARNING

 

 

READ and UNDERSTAND this manual completely before using rough cut mower. 

All operators of this equipment must read and completely understand all safety information, operating instructions, 

maintenance and storage instructions. Failure to properly operate and maintain the mower could result in serious injury or 

death to the operator and bystanders from moving parts that can cut, amputate, flying objects, burns, fire or explosion or 

carbon monoxide poisoning and be aware of the following hazards. 

 

WARNING

: Keep all guards and shields in place to avoid injury.  

 

DANGER

: Do not operate the rough cut mower near people. Debris can be thrown hundreds of feet. Clear work area of 

foreign objects and debris. Debris thrown by rough cut mower can cause serious injury or death. 

 

CAUTION

: Avoid fires. Keep the machine clean of debris, trash and any other flammable material. 

 

WARNING

: Tighten all nuts and bolts before starting. Replace or repair any safety device, bolts, etc if damaged or worn. 

 

DANGER

: Stay clear of rotating blades. Keep hands and feet away. 

 

DANGER

: Never operate rough cut mower without it mounted securely to the tow vehicle. 

 

WARNING

: Wear protective clothing. Wear close-fitting clothing and other protective devices appropriate for the job. 

 

DANGER

: Keep riders off machine. Riders can be seriously injured or killed by entanglement or by falling. 

 

DANGER

: Exercise caution while working near machine. Failure to heed warnings may lead to serious injury or death.  

 

DANGER

: Always maintain a safety distance. Never operate rough cut mower with bystander’s present. The rough cut 

mower creates a serious discharge hazard.  Never point the discharge direction at anyone.  Be aware of where bystanders 

are located, especially children.  Never assume they will remain where you last saw them.  Be sure to know what is in the 

path of the discharge area. 

STOP! 

 

ADD OIL TO ENGINE BEFORE USING: Engine is shipped without oil. DO NOT start rough cut mower without first adding oil.  

INSPECT COMPONENTS: Closely inspect to make sure no components are missing or damaged.  

See Initial Unpacking and Set-up for instructions and for whom to contact to report missing or damaged parts. 

 

ITEM NUMBERS: 

 BRPRC108HEB 

 

 

MANUAL SERIAL TAG HERE 

 

 

 

 

    

 

 

 

 

 

 

 

 

    

 

 

 

 

 

 

 

      

Summary of Contents for BRPRC108HEB

























Reviews: