bluMartin freeAir100 Service Download

Page: 1 / 18

Service

[ S ] 32

Service

Notes

• The annual filter change does not require any tools.
• Original bluMartin replacement filters are available from the installer, from us

(

[email protected]

) or from Amazon.

• You need a Torx-10- and a Torx-20 screw driver for installation and service tasks.

DANGER

Observe all references to safety and use of the freeAir100 in part General [G].

Device Test

After correct installation turn the freeAir100 on and wait a few minutes while the device

executes a test routine.

Test Turbo operation once either only blue LEDs or no LEDs are illuminated.

Connect Software

For control of device functions and for any update,

we recommend:
•  Laptop (Windows 7 or 8)
•  USB cable (A on B)
•  Our free software freeAir-Connect

and free updates for freeAir100

(

www.bluMartin.de/service/downloads

Summary of Contents for freeAir100



















Search results

Summary of Contents for freeAir100

Reviews:

Related manuals for freeAir100

Brands by name

Popular brands

bluMartin freeAir100, Service

Search results

Summary of Contents for freeAir100

Reviews:

Related manuals for freeAir100

Brands by name

Popular brands