background image

128-7853A

1 of 16

1

Model  APS-920

Installation Manual

This Remote Start/Alarm System is designed to be used with

Automatic Transmission-Fuel Injection Vehicles Only!

COMPONENTS:

Control Module
1 Four Button RF Transmitter
1 Four Button LCD Transmitter
2 Way Antenna/Receiver
1 “1 X 1.75” Foam Pad
6 Pin Main Power Harness w/Fuses
20 Pin Accessory Harness
1 Hood Pin Switch
1/4” Female Spade Connector

2 Pin Door Lock/Unlock Harness
Starter Inhibit Relay & Harness
2 Pin LED Assy
2 Pin Push-Button Valet/Program Switch
4 Pin Antenna Receivers Harness
4 Pin Auxiliary Output Harness
Installation/Owners Guide
4 Philips Head Black Drill Point Sheet
Metal Screw #8 X 1/2"

FEATURES:

Selectable Ignition Lock & Unlock
Selectable Door Lock/Unlock Output Timing
Safe Start (Requires double push of the start button to engage the remote start function)
On Board Parking Light Relay
Trunk Release Output
Horn Chirp Output With Duration Select
Selectable RF Start Chirp
Panic Mode (Can select to have horn along with parking lights)
Selectable Run Times 5, 10, 15, or 20 Minutes
Selectable Gas or Diesel
Automatic Start Timer (Can be set to start your car automatically at 2 or 4 hour intervals)
4 Negative Pulsed Aux Outputs Before Start, After Start, During Crank, After Shut Down
(To aid installation in many vehicles with factory alarm systems)
Turbo Timer
Dual Stage Shock Sensor
Shock Sensor Shunt During R/S Selectable

FCC NOTICE

This device complies with part 15 of the FCC rules. Operation of this device is subject to the
following conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.

Caution:

 Changes or modifications not expressly approved by the party responsible for

compliance voids the users authority to operate this device.

Rev A To I Door Lock Outputs Reference Omitted In The Original Draft 7/23/08

Summary of Contents for Prestige APS-920

















Reviews: