BX-Series Checkweighing Floor Scale
Side A
TM
Installation & Assembly
Models
&
Capacities
BX-120+
120 x 0.02 lb
BX-150
150 x
0.05
lb
BX-300+
300 x 0.05 lb
BX-300
300 x
0.1 lb
BX-600+
600 x 0.1 lb
BX-600
600 x
0.2 lb
Pole & Display:
Assembly of the pole display is required.
Please follow the Assembly Instructions on Side B:
1. Insert load cell cable through pole and insert pole
into the bottom bracket. Tighten all screws.
2. Attach the top bracket to the Display Head and feed
the load cell cable through the top bracket and
connect it to the back of the Display Head.
3. Tighten all screws and adjust the Display Head.
4. Remove the Lock Bolt from underneath the platform.
Initial Setup:
Plug the AC adapter cable into the rear of
the display head and then the adapter into an AC outlet.
Some units have a fixed AC Cord instead of an adapter.
On/Off Key:
The
On/Off
Key must be held down for
more than one second in order to turn the scale ON.
Operating the Scale
Make sure the platter is sitting properly on top of the
platform and that there is nothing on top of the platter.
Also, make sure that the scale is plugged into the proper
outlet. Hold down
until the scale display begins to
show the self test and then release the key. This is the
Initial State and displays appear like this:
The number of zeroes and decimal places may vary
depending on model and capacity.
Simple Weighing:
1. Place an item on the platter
2. The Stable Lamp will indicate a stable weight
3. Remove the item from the platter
Weighing Using Tares:
1. Place the empty container on the platter
2. Press
and then place an item on the platter
3. The Stable Lamp will indicate a stable weight
4. Remove the item from the platter
Once you press
, you will notice that the NET Lamp
will come on indicating to you that the weight shown is a
net weight. For example, this is what the display would
look like after you press
:
However, after Step 4 the display may look like this:
In this example, the platter is empty and the tare was set
using an empty container that weighs 2.50 pounds.
Clearing Tares:
1. Make sure that there is nothing on the platter
2. Press
and the display will show:
You are back to the Initial State.
Using the Unit Key:
1. Press
and the weighing units will change
2. Repeat Step 1 until you reach the units you desire*
You can use the
key in combination with/without tares
or with/without any weight on the platter. The scale offers
the following units: Pounds (lb), Ounces (oz), Kilograms,
(kg), Grams (g), Counting (Pcs), Percentage (%), and
Pound-Ounce (lb oz).
*Note
however that Counting,
Percentage, and Pound-Ounce are
not
to be used in Legal
for Trade applications.
Counting and Percentage Weighing:
1. Follow Unit key instructions to get to
Pcs
or
%
units
2. Press and hold down
until the display shows:
3. Release the
key. You can select to sample with
10, 20, 50, 100, or 500 pieces* by using the
key.
4. Place the indicated number of piece on the platter and
then press
. The scale will show Pcs or % values.
*Note
that when using Percentage, the scale will sample
with 10, 20, 50, 100, or 500 %.
Using the Mode Key:
1. Press
and the weighing units will change
2. Repeat Step 1 until you reach the mode you desire*
You can use the
key in combination with/without tares
or with/without any weight on the platter. The scale offers
the following modes: Weighing1, Weighing2, Limit, and
Hold.
*Note
however that Weighing2 and Hold modes are
not
to be used in Legal for Trade applications.
Charging the Battery
The
Lamp is located on the top left side of the display.
When it turns ON you need to recharge the battery. The
scale can be ON or OFF when recharging so long as it is
plugged into an AC outlet. The Recharge LED is located
above the
key and shows various states which are
explained on the other side of this guide. An overnight
charge of 12 hours, will yield approximately a 90% charge
or about 90 hours of continuous use (no-backlight.)
