1
A-100IMWP
ILLUMINATED MULLION KEYPAD
WIRING & PROGRAMMING INSTRUCTIONS
WI1497 7/06
GENERAL DESCRIPTION
The A-100IMWP is a self-contained access control keypad
designed outdoor applications. Its heavy stainless steel mul-
lion-style surface mount enclosure is designed to be used in
narrow stile applications. The A-100IMWP operates up to
three outputs (two relays and 1 open-collector transistor)
and can be used to trigger a door strike, an electromagnetic
door lock, or any other relay-activated device. Programming
is performed manually at the keypad, allowing up to 150 indi-
vidual Users, each with their unique User Codes. The A-100
Series includes the indoor stainless steel A-100 (see
WI1495) and the rugged sealed environment A-100WP (see
WI1496).
In a typical application, the A-100IMWP will energize one or
both relays upon the keypad entry of a valid User Code.
Outputs 1 and 2 are two relays of the three contact Form C
type, and Output 3 is an open collector transistor (terminal
labeled "OC") that switches "on" (closes with the ground ter-
minal) when energized. The length of time the outputs are
energized (their "activation duration") can be programmed to
between 1 and 99 seconds. A Request-to-Exit button will
momentarily short Output 1 by wiring terminals M and P1
using a normally-open momentary-close switch.
To program the keypad functions you must first perform the
initial startup procedure, then enter
Program Mode
by press-
ing the Master Code at the keypad. Once in Program Mode,
all system functions can be accessed and programmed.
Exit Program Mode to put the keypad (with its new program-
ming) into use.
SPECIFICATIONS
•
12 to 24VDC (polarized) or 12 to 24VAC voltage input
•
Output 1: 5A/250VAC relay
•
Output 2: 1A/125VAC relay
•
Output 3: 250mA open collector
•
Capacity of 150 User Codes of 3 to 6 digits
•
Output activation duration programmable from 01-99
seconds (program "00" to select "toggle" mode)
•
All programming stored in non-volatile EEPROM mem-
ory
•
Orange LED Keypress feedback
•
Output #1 relay activation duration programmable per
user code
•
Keypad illumination duration programmable from 10-99
seconds (for backlit keypad models only)
•
Tamper switch output terminals (S1 - S2) on PCB
•
Sounder feedback "beeps" can be activated or deacti-
vated for user code entries
•
Operating Temperature: -13°F to 131°F
-25°C to +55°C
•
Dimensions (WxHxD): 1¾" x 6½" x 1 1/8"
4.4cm x 16.5cm x 2.9cm
•
Operating Voltage: 12VDC to 28VDC
10VAC to 26 VAC
•
Maximum Current Draw:
12VDC: 15mA (Standby) 108mA (Active)
24VDC: 21mA (Standby) 125mA (Active)
12VAC: 33mA (Standby) 192mA (Active)
24VAC: 54mA (Standby) 233mA (Active)
GETTING STARTED
First Time Startup--Self-Test
After you unpack the lock from its factory packaging, we
recommend you perform the initial startup procedure
(outlined below). For keypads already in use, this startup
procedure can also be used to erase all existing keypad
programming and return the keypad back to its original
"out of box" factory default condition.
1.
Install the jumper
located on the back of the keypad
(right position).
2.
Apply power
(12-24VDC polarized or 12-24VAC) to
the power input terminals.
•
Orange LED blinks once
3.
Press
7890#123456*
•
Red LED turns ON
•
Orange LED turns ON
•
Green LED turns ON
345 Bayview Avenue
Amityville, New York 11701
For Sales and Repairs 1-800-ALA-LOCK
For Technical Service 1-800-645-9440
Publicly traded on NASDAQ Symbol: NSSC
© ALARM LOCK 2006
A-100IMWP Wiring Table
Description
Wire Colors
+ 12V or 24V AC/DC Input
Red
– Ground
Black
Request to Exit Input
Purple
Request to Exit Input
Pink
Relay 1 Normally Open
Yellow
Relay 1 Common
Brown
Relay 1 Normally Closed
Dark Blue
Relay 2 Normally Open
Light Blue
Relay 2 Common
Light Green
Relay 2 Normally Closed
Orange
Open Collector Output
Dark Green
Tamper SW Output
Gray
Tamper SW Output
White
