ADC ADCP-90-250 User Manual Download

Page: 1 / 15

ADCP-90-250

Issue 1, November 1996

4-40001-2326 Page 1



1996, ADC Telecommunications, Inc.

FTD1 36-Fiber Wall Box

User Manual

Content Page

INTRODUCTION

...........................................................................

Revision History

.......................................................................

Trademark Information

..................................................................

Admonishments

.......................................................................

1. DESCRIPTION

.........................................................................

A. Functional Description

...............................................................

B. Physical Description

................................................................

C. Technical Description

...............................................................

2. INSTALLATION

........................................................................

A. Wall Mounting the Wall Box

...........................................................

B. Rack Mounting the Wall Box

..........................................................

C. Installing Wall Box Components

.......................................................

D. Replacement Procedure — Key Locks

..................................................

3. OPERATION

.........................................................................

A. Cleaning the Connectors and Adapters

.................................................

B. Routing the Patch Cords in the Wall Box

................................................

4. SYSTEM INTEGRATION SERVICES

.......................................................

5. CUSTOMER SUPPORT SERVICES

........................................................

INTRODUCTION

This user manual describes the features and functions of ADC’s FTD1 36-Fiber Wall Box. Also
included are the wall box installation and operation procedures.

Revision History

ISSUE DATE REASON FOR CHANGE

1 11/96 Original

Trademark Information

Hubbell is a registered trademark of Hubbell Incorporated

Summary of Contents for ADCP-90-250
















Search results

Summary of Contents for ADCP-90-250

Reviews:

Related manuals for ADCP-90-250

Brands by name

Popular brands

ADC ADCP-90-250, User Manual

Search results

Summary of Contents for ADCP-90-250

Reviews:

Related manuals for ADCP-90-250

Brands by name

Popular brands