ZyXEL Communications XGS1210-12 User Manual Download Page 23

Page: 23 / 82

Chapter 4 Web Configurator

XGS1210-12 / XGS1250-12 User’s Guide

• Core i3 processor
• 2 GB RAM
• 100 MB free hard disk
• WXGA (Wide XGA 1280 by 800)

4.3.2 Run the ZON Utility

Double-click the ZON Utility to run it.

The first time you run the ZON Utility, you will see if your device and firmware version support the ZON
Utility. Click the

button to close this screen.

Figure 16

Supported Devices and Versions

If you want to check the supported models and firmware versions later, you can click the

Show

information about ZON

icon in the upper right hand corner of the screen. Then select the

Supported

model and firmware version

link. If your device is not listed here, see the device release notes for ZON

Utility support. The release notes are in the firmware zip file on the Zyxel web site.

Summary of Contents for XGS1210-12



















































































Search results

Summary of Contents for XGS1210-12

Reviews:

Related manuals for XGS1210-12

Brands by name

Popular brands

ZyXEL Communications XGS1210-12, User Manual

Search results

Summary of Contents for XGS1210-12

Reviews:

Related manuals for XGS1210-12

Brands by name

Popular brands