manualshive.com logo in svg

ZyXEL Communications Prestige P128, Release Note, Page: 10 / 17

Share
Download
ZyXEL Communications Prestige P128 Release Note Download Page 10

10

               Menu 24.2.1 - System Maintenance - Information

                    Name: 1.5FCS
                    Routing: IP/IPX
                    RAS S/W Version: V1.50(B.00) | 8/17/98
                    ISDN F/W Version: V 07f
                    Country Code: 255

                    LAN
                      Ethernet Address: 00:a0:c5:40:00:ee
                      IP Address: 204.237.202.151
                      IP Mask: 255.255.255.192
                      DHCP: None

Menu 24.1 only displays the dynamic information now. The B-channel instead of the logical
channel is shown under 

CHAN

 now. The CLID of the incoming data or voice call will be shown

on this menu too. So is WAN IP address.

                   Menu 24.1 - System Maintenance - Status

CHAN   Link     Type        TXPkt       RXPkt       Error  CLU  ALU     Up Time
 B1      isp        64Kbps     28923       25392           0    12%   1%      0:28:24
 B2      Voice     0Kbps      15521       13194           0      0%   0%      0:00:00

     Total Outcall Time:    11:31:06

     Ethernet                                 WAN
       Status: 10M/Half Duplex         B1 IP Addr: 202.237.102.121
       TX Pkt: 59389                         B2 IP Addr:
       RX Pkt: 126924                       B1 CLID:
       Collision: 3                              B2 CLID: 12345

     LAN Packet Which Triggered Last Call: (Type: IP)

     45 00 00 38 7D 14 00 00 3F 11 C8 0B CA E7 BB 61 9D 16 01 06 00 35 00 35
     00 24 39 90 79 65 00 00 00 01 00 00 00 00 00 00 06 64 6F 6D 61 69 6E 03

                               Press Command:
   COMMANDS: 1-Drop B1  2-Drop B2  3-Reset Counters  4-Drop All  ESC-Exit

5 Bug fixes

1. Some Prestige users experienced system hang once a couple of weeks. When it happened,

it needed human intervention to power cycle the Prestige for making it work again. In this
release, Prestige will re-boot itself to eliminate the human intervention.

2. Prestige used to have a bug in its SUA mechanism. This bug caused Prestige dropping the

fragmented WAN incoming IP packets. The symptom is that you have problems to certain
Web sites if the Prestige is configured SUA. It is fixed in this release.

Summary of Contents for Prestige P128


















Reviews:

No comments