ZyXEL Communications Nebula NSG Series User Manual Download Page 47

Page: 47 / 55

Appendix B Legal Information

NSG Series User’s Guide

List of national codes

Safety Warnings

• Do NOT use this product near water, for example, in a wet basement or near a swimming pool.

• Do NOT expose your device to dampness, dust or corrosive liquids.

• Do NOT store things on the device.

• Do not obstruct the device ventillation slots as insufficient airflow may harm your device. For example, do not place the device in an

enclosed space such as a box or on a very soft surface such as a bed or sofa.

• Do NOT install, use, or service this device during a thunderstorm. There is a remote risk of electric shock from lightning.

• Connect ONLY suitable accessories to the device.

• Do NOT open the device or unit. Opening or removing covers can expose you to dangerous high voltage points or other risks. ONLY qualified

service personnel should service or disassemble this device. Please contact your vendor for further information.

• Make sure to connect the cables to the correct ports.

• Place connecting cables carefully so that no one will step on them or stumble over them.

• Always disconnect all cables from this device before servicing or disassembling.

• Use ONLY an appropriate power adaptor or cord for your device. Connect it to the right supply voltage (for example, 110V AC in North

America or 230V AC in Europe).

• DO NOT remove the plug and connect it to a power outlet by itself; always attach the plug to the power adaptor first before connecting it to

a power outlet.

• Do NOT allow anything to rest on the power adaptor or cord and do NOT place the product where anyone can walk on the power adaptor

or cord.

• Do NOT use the device if the power adaptor or cord is damaged as it might cause electrocution.

• If the power adaptor or cord is damaged, remove it from the device and the power source.

• Do NOT attempt to repair the power adaptor or cord. Contact your local vendor to order a new one.

• DO NOT use the device outside, and make sure all the connections are indoors. There is a remote risk of electric shock from lightning.

• CAUTION: RISK OF EXPLOSION IF BATTERY (on the motherboard) IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES

ACCORDING TO THE INSTRUCTIONS. Dispose them at the applicable collection point for the recycling of electrical and electronic equipment.

For detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the

store where you purchased the product.

• Use ONLY power wires of the appropriate wire gauge for your device. Connect it to a power supply of the correct voltage.

• Fuse Warning! Replace a fuse only with a fuse of the same type and rating.

• The POE (Power over Ethernet) devices that supply or receive power and their connected Ethernet cables must all be completely indoors.

• This equipment must be grounded by qualified service personnel. Never defeat the ground conductor or operate the equipment in the

absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are

uncertain that suitable grounding is available.

• When connecting or disconnecting power to hot-pluggable power supplies, if offered with your system, observe the following guidelines:

- Install the power supply before connecting the power cable to the power supply.
- Unplug the power cable before removing the power supply.
- If the system has multiple sources of power, disconnect power from the system by unplugging all power cables from the power supply.

• The following warning statements apply, where the disconnect device is not incorporated in the equipment or where the plug on the power

supply cord is intended to serve as the disconnect device,
- For PERMANENTLY CONNECTED EQUIPMENT, a readily accessible disconnect device shall be incorporated external to the equipment;
- For PLUGGABLE EQUIPMENT, the socket-outlet shall be installed near the equipment and shall be easily accessible.

• CLASS 1 LASER PRODUCT

• APPAREIL À LASER DE CLASS 1

• PRODUCT COMPLIES WITH 21 CFR 1040.10 AND 1040.11.

• PRODUIT CONFORME SELON 21 CFR 1040.10 ET 1040.11.

COUNTRY

ISO 3166 2 LETTER CODE

COUNTRY

ISO 3166 2 LETTER CODE

Austria

Liechtenstein

Belgium

Lithuania