background image

        

 

 

 

This is not a service contract, and this warranty does not include maintenance, cleaning, or periodic 
check-up. During the period specified above, Zylight will replace defective parts at its expense, and 
will absorb all expenses for warranty service and repair labor by reason of defects in material or 
workmanship. The sole responsibility of Zylight under this warranty shall be limited to the repair of 
the product, or replacement thereof, including parts, at the sole discretion of Zylight. All products 
covered by this warranty were manufactured after April 1, 2014, and bear identifying marks to that 
effect.

Zylight reserves the right to make changes in design and/or improvements upon its products 
without any obligation to include these changes in any products theretofore manufactured.

No warranty, whether expressed or implied, is given or made with respect to any accessory supplied 
with products described above. Except to the extent prohibited by applicable law, all implied 
warranties made by Zylight in connection with this product, including warranties of merchantability 
or fitness, are limited in duration to the warranty period set forth above. And no warranties, whether 
expressed or implied, including warranties of merchantability or fitness, shall apply to this product 
after said period has expired. The consumer's and or dealer's sole remedy shall be such repair or 
replacement as is expressly provided above.

This warranty is the only written warranty applicable to Zylight Products and supersedes all prior 
warranties and written descriptions of warranty terms and conditions heretofore published. Under 
no circumstances shall Zylight be liable for any loss or damage, direct or consequential, arising out 
of the use of, or inability to use, this product.

This warranty gives you specific legal rights, and you may also have other rights which vary from 
state to state.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two 
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any 
interference received, including interference that may cause undesired operation. Changes or 
modifications not expressly approved by the party responsible for compliance could void the user's 
authority to operate the equipment.
 
Per FCC 15.105(a), Note: This equipment has been tested and found to comply with the limits for a 
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference when the equipment is operated in a commercial 
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not 
installed and used in accordance with the instruction manual, may cause harmful interference to 
radio communications. Operation of this equipment in a residential area is likely to cause harmful 
interference in which case the user will be required to correct the interference at his own expense.

 
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to 
the following two conditions: (1) this device may not cause interference, and (2) this device must 
accept any interference, including interference that may cause undesired operation of the device.
 
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio 
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit 
pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage 
radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
 
 

F.

G.

H.

I.

Register your instrument at - www.zylight.com/product-registration

E.

        

 

 

 

 

 

 

                             Warranty Cont.

Page 15

Summary of Contents for F8-200





















Reviews: