background image

 

18

 

 

 

 

The 

MAHCL4X4 

is guaranteed, free of material and workmanship defects for up to two (2) years from 

the  Date  Code  by  ZuumMedia  or  an  approved  authorized  dealer.  Should  this  product  fail  to  be  in  good 
working condition within two (2) years from the date code, ZuumMedia, at its option, will repair or replace the 
unit,  provided  that  the  unit  has  not  been  subjected  to  abuse,  static  discharge,  power  surge  or  any 
unauthorized modifications and disassembly. Warranty provided by ZuumMedia to its BUYER is with direct 
transaction only and warranty is void if the warranty seal on the metal housing is broken. 

A unit that fails under conditions other than those covered will be repaired at the current price of parts 

and labor in effect at the time of repair. Such repairs are warranted for 90 days from the day of reshipment to 
the BUYER. If the unit is delivered by mail, the customer agrees to insure the unit or assume the risk of loss 
or damage in transit. Under no circumstances will a unit be accepted without a return authorization number 
(RA). 

The  warranty  is  in  lieu  of  all  other  warranties  expressed  or  implied,  including  without  limitations,  any 

other  implied  warranty  or  fitness  or  merchantability  for  any  particular  purpose,  all  of  which  are  expressly 
disclaimed. 

The content of this manual has been carefully checked and is believed to be accurate. However, The 

SELLER assumes no responsibility for any inaccuracies that may be contained in this manual. The SELLER 
will NOT be liable for direct, indirect, incidental, special, or consequential damages resulting from any defect 
or omission in this manual, even if advised of the possibility of such damages. Also, the technical information 
contained herein regarding the 

MAHCL4X4

 features and specifications is subject to change without further 

notice. 

 

WARRANTY   

Summary of Contents for MAHCL4X4





















Reviews: