background image

FV606 Rev.  A  8/6/2018

Page 11

    

Maintenance  Instructions: 

• Do not use any abrasive or chemical cleaners to clean the sink, faucet and other components.

• 

If abrasives or chemicals are used it can lead to dulling of luster, attacking of chrome plating or decorative finishes.

• ONLY use mildly warm soapy water, and then wipe dry with a clean/soft towel or cloth.

• When cleaning other areas of the restroom be sure the sensor lenses are protected from other cleaning chemicals/

solvents to prevent potential damages to the sensor and/or electronics.

• For surface shine, rubbing a polishing agent will polish the surface of all components.

• Frequent proper cleaning of solid surface sink will maintain the gloss level over time.  Also, darker colors require more 

frequent cleaning and care.  Dirt and residue can easily be removed from the basin surface by using water, mild soap 

solution, household ammonia-based  cleaners, and/or solid surface cleaners available in market.

• In order to remove hard water and difficult stains on basin surface, use a sponge with diluted cleaner to rub in a circular 

motion.  To disinfect basin surfaces, wipe the area with diluted bleach and then wash the surfaces and rinse with water.

• Avoid exposing solid surface basin with strong chemicals, such as acetone-based cleaners and solutions.  If surfaces 

are exposed to these chemicals, quickly rinse the surface with water.

Repair Instructions: 

• 

Zurn recommends that damages should be repaired by certified solid surface fabricator or repair agents.

• Blemishes to the basin surface (such as scratches, burnmarks, and minor chipping) can be repaired by sanding with 

super-fine(800 or 1000 grit) sand paper and/or maroon Scotch-Brite™ pads and then followed with a low-speed (1500-

2000 rpm) polisher with a wool pad and a solid surface cleaner or polish to buff the affected area. 

• For more serious damage to the basin (size of a dime or larger), repair kits and instructions are available to purchase.  

Contact customer service for further information on ordering.

Trouble Shooting Guide: 

Service Parts:

Faucet Related Issues Refer to Faucet Manual included with faucet
Soap Dispenser Issues Refer to Soap Dispenser Manual included with soap dispenser

Part Number

Part Description 

QTY

P5001-GD-PC

Grid Drain Assembly for Reef Basin

1

P5000-DA

Drain Adapter Assembly

1

P5000-WH

Wall Hanger Assembly

1

P5000-BKT

Mounting (L) Bracket Assembly for  Reef Basin

1

P5001-SS1

Stainless Steel Shroud for Reef Basin

1

P5000-DA-BAG Drain Adapter/Stainless Steel Shroud Hardware Bag

1

P5000-WH-BAG Wall Hanger Bracket Hardware Bag

1

P5000-BKT-BAG Mounting (L) Bracket Hardware Bag

1

Summary of Contents for Sundara Z5001.02












Reviews: