ZTEWelink MF206A Hardware Development Manual Download Page 80

Page: 80 / 88

Hardware Development Guide of Module Product

MF206A

panels are reserved in the center of the module. During the connection with the system board, make sure that

these wielding panes are grounded well, which is greatly helpful to heat conductivity and heat balance, and is

greatly beneficial to the electric performance of the whole set as well.



NOTE:

1. Keep this product away from heat-dissipation devices with high power, to prevent the temperature of the

module from being too high.

2. Do not put the module close to the large heat-dissipation devices, such as CPU or bridge. The high

temperature will affect the RF performance.

9.4

Recommended Product Upgrading Plan

It’s recommended to use the one-click software upgrade tool to upgrade through the USB port provided by

ZTEWelink in the Windows system. If the customer wants to upgrade the module in other operation systems,

ZTEWelink provides the corresponding reliable tools as well.

Summary of Contents for MF206A
























































































Search results

Summary of Contents for MF206A

Reviews:

Related manuals for MF206A

Brands by name

Popular brands

ZTEWelink MF206A, Hardware Development Manual

Search results

Summary of Contents for MF206A

Reviews:

Related manuals for MF206A

Brands by name

Popular brands