Zte ZXR10 3800-8 Handling Manual Download Page 188 | Manualshive

Page: 188 / 307

background image

ZXR10 Alarm Handling Manual

Cause

The hold time interval of Hello ought to be longer than Hello report
interval.

Recommended

Operations

Check mpls hello hold time interval and hello report interval
please; the correct configuration ought to be that hello hold time
interval is longer than hello report interval.

201

Message No.

201

Cause

The flash is under application.

Recommended

Operations

Please try again later.

202

Message No.

202

Cause

Incorrect copy type

Recommended

Operations

Please configure correct command.

203

Message No.

203

Cause

The (T) FTP server does not respond.

Recommended

Operations

Check whether the line connection and server operation are nor-
mal.

204

Message No.

204

Cause

Start to copy.

Recommended

Operations

Informational notice. No action is needed.

206

Message No.

206

Cause

Fail in Network-to-network copy.

156

Confidential and Proprietary Information of ZTE CORPORATION

«
...
186
187
188
189
190
...
»

Summary of Contents for ZXR10 3800-8




















































































































































































































































































































Reviews:

No comments

Related manuals for ZXR10 3800-8

Brand: Patton electronics Pages: 2

ipRocketLink 3086FR

Brand: Patton electronics Pages: 6

Brand: Patton electronics Pages: 16

Brand: Patton electronics Pages: 51

Brand: Funkwerk Pages: 2

Brand: Radicom Pages: 27

Brand: Thecus Pages: 120

Brand: Pakedge Device & Software Pages: 14

802.11a/b/g SDIO WiFi Module SDM3100

Brand: Abocom Pages: 14

Brand: UNICORECOMM Pages: 19

Brand: CAME Pages: 32

Brand: NetComm Pages: 65

Airborne M2M ABDN-er-DP55 Series

Brand: B+B SmartWorx Pages: 120

Brand: Matrix Switch Corporation Pages: 60

Brand: TRENDnet Pages: 57

TeraStation WSS WS5020N6

Brand: Buffalo Pages: 115

Brand: Black Box Pages: 62

SecPath F50X0 Series

Brand: H3C Pages: 41

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands