Zte ZXMBW E9230 User Manual Download Page 58

Page: 58 / 71

ZXMBW E9230 User Manual

IGURE

46 A

NTENNA

NSTALLATION

OSITION

Lightning rod

45° Lightning protection area

Antenna

Grounding cable

Following are lightning protection requirements to install an an-
tenna:

�

The antenna should be installed with in 45° coverage area of
lightning rod.

�

If there is no special lightning protection arrangement like the
above, install the lightning protection system onto the antenna
pole.

�

Make sure that the lightning rod is well grounded.

Note:

This section introduces the installation process of directional an-
tenna briefly. Refer to the installation guide delivered with the
antenna for detailed installation steps.

Steps

1. Assemble parts of directional antenna.

Firstly assemble fastener "C" onto the upper and lower ends
of antenna as shown in

Figure 47

. Then mount fasteners "B"

and "A" to complete the initial installation of the directional
antenna.

Confidential and Proprietary Information of ZTE CORPORATION

Summary of Contents for ZXMBW E9230








































































Search results

Summary of Contents for ZXMBW E9230

Reviews:

Related manuals for ZXMBW E9230

Brands by name

Popular brands

Zte ZXMBW E9230, User Manual

Search results

Summary of Contents for ZXMBW E9230

Reviews:

Related manuals for ZXMBW E9230

Brands by name

Popular brands