Zte ZXMBW E9230 User Manual Download Page 59

Page: 59 / 71

Chapter 3 Equipment Installation

IGURE

47 D

IRECTIONAL

NTENNA

NSTALLATION

2. Fix the directional antenna to the pole.

Attach the antenna along with fixtures onto the pole. Do not
tighten the screws too tightly to allow easy adjustment of the
direction and downtilt of the antenna.

However, degree of

tightness must be appropriate enough to ensure that the an-
tenna does not slid downward.

3. Adjust the antenna's azimuth.

Determine the azimuth of the antenna by using a compass,
and determine the installation direction according to the
engineering design drawing.

ii. Turn the antenna slightly to adjust it's face direction as

shown in

Figure 47

. At the same time, measure the direc-

tion of the antenna with a compass until the error comes
within the engineering design requirements (generally not
more than 5°).

iii. After adjusting the azimuth of the antenna, tighten the fas-

tener "A".

4. Adjust the antenna's downtilt.

Adjust the downtilt of the measurement meter to obtain
the required angle according to the engineering design.

ii. Turn the top of the antenna slightly, and loose or fast the

antenna at its top. Adjust the downtilt angle of the antenna
till the measurement meter's bubble comes to be centered
as shown in

Figure 48

Confidential and Proprietary Information of ZTE CORPORATION

Summary of Contents for ZXMBW E9230








































































Search results

Summary of Contents for ZXMBW E9230

Reviews:

Related manuals for ZXMBW E9230

Brands by name

Popular brands

Zte ZXMBW E9230, User Manual

Search results

Summary of Contents for ZXMBW E9230

Reviews:

Related manuals for ZXMBW E9230

Brands by name

Popular brands