background image

                              ZXHN H368C User’s Manual

 

17 

6. 

Connection to party line service is subject to state tariffs. Contact the 

state public utility commission public service commission or corporation 

commission for information. 

 

7. 

If the telephone company requests information on what equipment is 

connected to their lines, inform them of: 

a) 

The telephone number that this unit is connected to, 

b) 

The ringer equivalence number [0.1B ] 

c) 

The USOC jack required [RJ11C], and 

d) 

The FCC Registration Number US: ZTEDL01BHNH368CV1 

Items (b) and (d) are indicated on the label. The ringer equivalence number 

(REN) is used to determine how many devices can be connected to your 

telephone line. In most areas, the sum of the RENs of all devices on any one 

line should not exceed five (5.0). If too many devices are attached, they may 

not ring properly. 

Service Requirements 

In the event of equipment malfunction, all repairs should be performed by our 

Company or an authorized agent. It is the responsibility of users requiring 

service to report the need for service to our Company or to one of our 

authorized agents. Service can be facilitated through our office at: 
Acadia Solutions, Inc.130 E. Wilson Bridge Road Suite 320 Worthington, OH 
43085. Phone

614-505-613 

 
 
 
 
 

 
 

Summary of Contents for ZXHN H368C


























Reviews: