background image

                              ZXHN H368C User’s Manual

 

15 

This equipment complies with FCC radiation exposure limits set forth for 

uncontrolled environment .This equipment should be installed and operated 

with minimum distance 20cm between the radiator& your body.     

This transmitter must not be co-located or operating in conjunction with any 

other antenna or transmitter. 

Note: This equipment has been tested and found to comply with the limits for a 

Class B digital device, pursuant to part 15 of the FCC Rules. These limits are 

designed to provide reasonable protection against harmful interference in a 

residential installation. This equipment generates, uses and can radiate radio 

frequency energy and, if not installed and used in accordance with the 

instructions, may cause harmful interference to radio communications. 

However, there is no guarantee that interference will not occur in a particular 

installation. If this equipment does cause harmful interference to radio or 

television reception, which can be determined by turning the equipment off and 

on, the user is encouraged to try to correct the interference by one or more of 

the following measures:     

Reorient or relocate the receiving antenna.     

Increase the separation between the equipment and receiver.     

Connect the equipment into an outlet on a circuit different from that to 

which the receiver is connected.     

Consult the dealer or an experienced radio/TV technician for help. 

 

 

 

 

 

 

Summary of Contents for ZXHN H368C


























Reviews: