background image

19

 

 

battery swelling or leakage. If the battery shows signs of 
swelling or leakage, please stop use immediately. 

Battery Safety   

• 

Using ZTE-unapproved or incompatible battery, charger or 
power adapter may damage your device, shorten its lifespan 
or cause a fire, explosion or other hazards. 

• 

The recommended operating temperatures are -10 °C to 55 °C 
and the storage temperatures are -20 °C to +60 °C. Extreme 
temperatures can damage the device and reduce the charging 
capacity and lifespan of your device and battery. 

• 

Do not place the device or the battery in or near heating 
equipment, such as microwave ovens, stoves or radiators. 
Keep the device and the battery away from excessive heat and 
direct sunlight. If not, the device or the battery may overheat 
and cause explosion or fire. 

• 

Please disconnect the charger when the battery is fully 
charged. Overcharging may shorten the battery life. 

• 

Do not short-circuit the battery, as this can cause excessive 
heat and fire. 

• 

Do not throw the battery into a fire to avoid explosion. 

• 

Do not disassemble, squeeze or puncture the battery, as this 
can cause explosion or fire. 

• 

When not using the battery for a long period, please charge 
the battery about half then remove the battery from your 
device and store it in a cool dry place. 

• 

If the battery damages or shows signs of swelling or leakage, 
please stop use immediately and contact ZTE or ZTE 
authorized service provider for replacement. 

• 

Return the worn-out battery to the provider or put it in the 
designated recycle place. Do not put it in household waste. 

• 

There is a risk of explosion if the wrong battery model is 

Summary of Contents for A004ZT


























Reviews: